Close
Home
Beading Instructions

Beading Resources > Free Beading Instructions > Projects > Bracelet with Czech Fire-Polished Glass Beads and Seed Beads

 Bracelet with Czech Fire-Polished Glass Beads and Seed Beads 

Courtesy of Preciosa®
CAEX


Budding of Spring

PRECIOSA ORNELA presents one of a group of trendy fashionable costume jewellery color combinations for spring and summer 2012 in an original wide bracelet sewn using seed beads and beads from the PRECIOSA Traditional Czech beads brand. The selection of the PRECIOSA seed beads and the bead colors evoke the magic of awakening nature contrasted by the refined light pastels of sprouting flowers and fresh leaves struggling through hard-skinned buds or a hardened crust of dried clay. We recommend the following colors: light grey, light pale blue, light lemon yellow, pale brown-green, green banana, olive brown, blue opal and light vitrail. The peyote stitch, which is one of the relatively simple, but highly effective seed bead sewing techniques, gives the bracelet the appearance of fabric. The correct tightening of the thread and the careful and error-free sewing of the seed beads into the gaps in the individual rows are important here.
: : : Materials : : :
  • Seed beads, Czech glass, #11 
  • Beading needles 
  • Scissors 
  • Rulers 
  • Bead, Czech fire-polished glass, 4mm
  • Bead, Czech fire-polished glass, 5mm
  • Bead, Czech fire-polished glass, 7mm
  • Pearl, imitation, 4mm
  • Pearl, imitation, 8mm
  • Flexible stringing material (Opelon, Elastomer, Lycra)

  • Optional:
  • Beads, Czech fire-polished glass 
  • Pearls 
  • Thread and cord 
  • End of Materials List

    The Procedure:

    The Peyote Stitch

    The basic principle of the peyote stitch involves sewing through the odd-numbered beads in the row, i.e. sew through every second seed bead from the second row (figures 2, 3a and 3b). First make a small sample in order to ascertain the correct number of seed beads in the first row. String a small amount (up to 10) of seed beads and sew at least four rows according to the basic procedure. Measure the sewn sample and compare it with the necessary dimensions. This will enable you to ascertain how many seed beads you need for the basic row, how many rows you will have to sew and how many seed beads you will need in total. It will be easier for beginners to try the procedure with an odd number of seed beads in the rows.

    Step 1
    Figure 1
    String one seed bead to begin the stringing (see the stop bead, figure no. 1). Then string the necessary number of seed beads in order to achieve the required width of the bracelet.
    Step 2
    Figure 2


    Figure 3a


    Figure 3b
    At the beginning of the second row, string one seed bead, pass the line through the penultimate seed bead from the first row and tighten the stringing. Continue in this way along the entire row, gradually string the individual seed beads and always pass the line through every odd-numbered seed bead from the previous rows. You can sew the individual seed beads precisely according to the design or you can use your own design. Sew the necessary number of rows: in this case, there are 85 rows. The standard length of the bracelet should be ca 18cm.
    Step 3
    Figure 4a


    Figure 4b
    After reaching the required length, sew the individual loops for closing the bracelet according to the drawing (figure no. 4a). Sew four 5mm fire-polished beads on the second side of the bracelet ca 1cm from the edge (figure no. 4b). Pass the needle and the doubled line through the sewn bracelet, string 1 rocaille, a bead and 1 rocaille. Then pass the needle and the line back through the strung bead, the rocaille and the sewn bracelet. Repeat this process of sewing through once again and overcast it on the bottom side and hide the ends between the seed beads. Tighten everything well and cut the line.
    Step 4
    Place the individual imitation pearls and fire-polished beads on the surface of the sewn bracelet and sew them on either according to the design or using your own imagination (figure no. 5).

    Have a question regarding this project? Email Customer Service.

    Copyright Permissions

    Permission to copy this instruction sheet is granted for non-commercial educational purposes only. All other reproduction requires written permission. Please email copyrightpermission@firemtn.com for more information.

    Products sold by Fire Mountain Gems and Beads® are intended for experienced jewelry-makers and designer-artists;
    children 14 years of age or younger should use these products with adult direction.

    Fire Mountain Gems and Beads, Inc. - One Fire Mountain Way, Grants Pass, OR USA 97526-2373
    Copyright 2008-2014 Fire Mountain Gems and Beads, Inc. All rights reserved.