Home
72-Hour Bead Bonanza

Sale ends in
00 hrs 00 mins 00 secs

Multi-Strand Bracelet with Copper Beads, Antiqued Copper-Plated Pewter Spacer Bars and Swarovski® Crystals

STEP 1
Cut the following lengths:
  • Ten 12-inch lengths of clear 0.8mm Powercord®
  • Twenty-five steel 25mm coils into approximately 1/4 inch pieces
STEP 2
Pass one 6mm jumpring through the one crystal AB 13x6.5mm briolette pendant then close.

Repeat to create the following briolette drops:
  • Fourteen crystal AB 13x6.5mm
  • Two crystal AB 11x5.5mm
  • Ten Indian pink 11x5.5mm
  • Nine copper 9x5mm
STEP 3
String the following onto one 12-inch length of Powercord:
  • Bead Stopper™
  • The first hole in one 58x3mm spacer bar
  • Repeat this sequence to string three sets:
    • One 5mm smooth round
    • One 9x4mm twisted corrugated oval
  • One 5mm smooth round
STEP 4
Continue to string the following:
  • The first hole in one 57x6mm spacer bar
  • Repeat this sequence to string five sets:
    • One 3mm smooth round
    • One 1/4 inch piece of coil
STEP 5
Repeat Steps 3 and 4 to string the second half of the strand.

Remove the Bead Stopper. Tie the two ends of the strand in a surgeon’s knot and insert into a bead.

Tip: Glue may be applied to the knot.
STEP 6
Repeat Steps 3 - 5 using the ninth holes in the spacer bars for the ninth strand.
STEP 7
String the following onto one 12-inch length of Powercord:
  • Bead Stopper
  • The second hole in one 58x3mm spacer bar (Step 3)
  • Repeat this sequence to string five sets:
    • One 1/4 inch piece of coil
    • One 3mm smooth round
STEP 8
Continue to string the following:
  • The second hole in one 57x6mm spacer bar (Step 4)
  • Repeat this sequence to string three sets:
    • One 5mm smooth round
    • One 9x4mm twisted corrugated oval
  • One 5mm smooth round
STEP 9
Repeat Steps 7 and 8 to string the second half of the second strand.

Remove the Bead Stopper. Tie the two ends of the strand in a surgeon’s knot and insert into a bead.
STEP 10
Repeat Steps 7 - 9 using the tenth holes in the spacer bars for the tenth strand.
STEP 11
String the following onto one 12-inch length of Powercord:
  • Bead Stopper
  • The third hole in one 58x3mm spacer bar (Step 3)
  • Repeat this sequence to string three sets:
    • One 5mm smooth round
    • One 9x4mm smooth oval
  • One 5mm smooth round
STEP 12
Continue to string the following:
  • The third hole in one 57x6mm spacer bar (Step 4)
  • Repeat this sequence to string five sets:
    • One 1/4 inch piece of coil
    • One 3mm smooth round
STEP 13
Repeat Steps 11 and 12 to string the second half of the third strand.

Remove the Bead Stopper. Tie the two ends of the strand in a surgeon’s knot and insert into a bead.
STEP 14
Repeat Steps 11 - 13 using the fifth holes in the spacer bars for the fifth strand and the seventh holes in the spacer bars for the seventh strand.
STEP 15
String the following onto one 12-inch length of Powercord:
  • Bead Stopper
  • The fourth hole in one 58x3mm spacer bar (Step 3)
  • Repeat this sequence to string five sets:
    • One 1/4 inch piece of coil
    • One 3mm smooth round
STEP 16
Continue to string the following:
  • The fourth hole in one 57x6mm spacer bar (Step 4)
  • Repeat this sequence to string three sets:
    • One 5mm smooth round
    • One 9x4mm smooth oval
  • One 5mm smooth round
STEP 17
Repeat Steps 15 and 16 to string the second half of the fourth strand.

Remove the Bead Stopper. Tie the two ends of the strand in a surgeon’s knot and insert into a bead.
STEP 18
Repeat Steps 14 - 17 using the sixth holes in the spacer bars for the sixth strand and the eighth holes in the spacer bars for the eighth strand.
STEP 19
Pass one 6mm jumpring through the first hole in the 58x3mm 10-strand spacer bar used in Step 3 then close. Repeat to add one 6mm jumpring to each of the 10 holes in the previous spacer bar.
STEP 20
Attach 3 - 4 briolette drops in the pattern of your choice to each of the previous 6mm jumprings.

: : : Additional Resources : : :

  • ''Glues'' how-to video and illustrated instructions

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You

Sign Up for Email Specials and Beading News
Sign Up
for Email Specials and Beading News