Hair Comb with Czech Glass Druk Beads and Swarovski Crystal

STEP 1
Using scissors cut two 18-inch and two 25-inch lengths of black Powercord®.
STEP 2
Align the combs next to each other with the solid edges to the inside. They will be designated as the left comb and right comb.
STEP 3
Pass the first 18-inch length of Powercord from the back to the front of the bottom left comb and back through the adjoining hole to the back of the comb. Tie the end of the cord using a double overhand knot to secure the cord in place. Pass the cord back through the lower bottom hole to the front of the comb.
STEP 4
Starting from the bottom hole on the left comb string onto the cord the following:
  • One 4mm round opaque green satin bead
  • One Swarovski 6mm bicone Montana AB bead
  • One 4mm round dark blue satin bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round translucent green luster bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round opaque green satin bead
  • One Swarovski 6mm bicone Montana AB bead
  • One 4mm round dark blue satin bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round translucent green luster bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round opaque green satin bead
  • One Swarovski 6mm bicone Montana AB bead
  • One 4mm round dark blue satin bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round translucent green luster bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round opaque green satin bead
STEP 5
Pass the Powercord through the middle hole on the right comb and back to the front of the comb through the adjoining hole. Pull the cord so that it is not too tight but the beads sit next to each other with no tension. String one Swarovski 6mm bicone Montana AB bead on the front of the holes, then pass the cord through the middle hole on the right comb and back to the front of the comb through the adjoining hole.
STEP 6
Repeat Step 4 backwards.
STEP 7
Pass the cord through the upper hole on the left comb and tie the cord using two overhand knots to secure the cord in place.
STEP 8
Repeat Steps 3 - 7 starting on the hole on the bottom right comb. Pass the beaded strand under the first strand from Step 4 and over the second strand from Step 6.
STEP 9
Pass the first 25-inch length of Powercord from the back to the front of the bottom left comb and back through the adjoining hole to the back of the comb. Tie the end of the cord using a double overhand knot to secure the cord in place. Pass the cord back through the lower bottom hole to the front of the comb.
STEP 10
Starting from the bottom hole on the left comb string onto the cord the following:
  • One 4mm round dark blue satin bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round translucent green luster bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round dark blue satin bead
  • One Swarovski 6mm bicone Montana AB bead
  • One 4mm round opaque green satin bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round translucent green luster bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round dark blue satin bead
  • One Swarovski 6mm bicone Montana AB bead
  • One 4mm round opaque green satin bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round translucent green luster bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round dark blue satin bead
  • One Swarovski 6mm bicone Montana AB bead
  • One 4mm round opaque green satin bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round translucent green luster bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round opaque green satin bead
  • One Swarovski 6mm bicone Montana AB bead
  • One 4mm round dark blue satin bead
  • One Swarovski 4mm bicone olivine satin bead
  • One 4mm round translucent green luster bead
STEP 11
Weave the strand between the previous strands before passing the Powercord through the upper hole on the right comb and back to the front of the comb through the adjoining hole to the inside.
STEP 12
String onto the cord eleven Swarovski 4mm bicone olivine satin beads.
STEP 13
Pass the cord through the middle hole on the right comb and back to the front of the comb through the adjoining hole to the inside.
STEP 14
String onto the cord eleven Swarovski 4mm bicone olivine satin beads.
STEP 15
Pass the cord through the bottom hole on the right comb.
STEP 16
Repeat Step 10 backwards.
STEP 17
Weave the strand between the previous strands before passing the cord through the upper hole on the left comb and tie the cord using two overhand knots to secure the knot.
STEP 18
Repeat Steps 9 - 17 starting on the hole on the bottom right comb. Weave the strands through the previous strands before passing them into the destination hole.
STEP 19
Use E-6000® Jewelry and Craft Adhesive according to manufacturer's instructions. Place adhesive in each of the holes on the back side of the combs over the knots to secure them in place. Let the adhesive set for 24 to 72 hours for maximum strength. Make sure to use proper ventilation when using this product.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You