Single-Strand Necklace and Earring Set with Swarovski Crystal, Accu-Flex® Beading Wire and Silver-Plated Brass Ribbon Crimp Ends

Necklace

STEP 1
Using flush-cutters, cut the following:
  • 130 3-inch lengths of clear Accu-Flex® professional-quality beading wire
  • One 2-inch length and one 4-inch length of silver-finished 9x6mm Figaro chain
STEP 2
Line up 26 3-inch lengths of beading wire. Place a piece of transparent tape over the end of the wires to hold the ends in place. Repeat to attach a piece of tape to the opposite end of the twenty-six 3-inch lengths of beading wire. Cut one end of the wires in an arch leaving one side of the wires 1-5/8 inches and the other side 2 inches in length. Trim the excess tape.
STEP 3
Pass one end of the taped beading wire into a ribbon end. Place a small amount of glue (E-6000® Jewelry and Craft Adhesive) on the inside of the ribbon end (optional). Using chain-nose pliers, compress the ribbon end over the wires. Repeat to attach a ribbon end to the opposite end of the beading wires.
STEP 4
Repeat Steps 2 and 3 to make a total of five beading wire components.
STEP 5
String one Swarovski crystal red magma 14mm twist onto an eyepin. Using a pair of chain-nose pliers, round-nose pliers and flush-cutters, form a simple loop on the straight end of the wire. Repeat to create four Swarovski crystal red magma 14mm twist beading links and one Swarovski crystal red magma14mm twist bead drop using one Swarovski crystal red magma 14mm twist and one headpin.
STEP 6
Using a pair of chain-nose pliers and flat-nose pliers, open a 4mm jumpring. Pass it through the loop on a lobster claw clasp and the first link of the 2-inch length of chain. Close the jumpring.

Open a 4mm jumpring. Pass it through the last link of the 2-inch length of chain and the loop on the first ribbon end. Close the jumpring
STEP 7
Continue to attach the following components:
  • Four sets of one Swarovski crystal red magma 14mm twist beading link and one beading wire component
  • One 4-inch length of chain
  • One Swarovski crystal red magma 14mm twist bead drop

Earrings

STEP 1
Using flush-cutters, cut 52 3-inch lengths of clear Accu-Flex beading wire.
STEP 2
Line up twenty-six 3-inch lengths of beading wire. Place a piece of transparent tape over the end of the wires to hold the ends in place. Repeat to attach a piece of tape to the opposite end of the twenty-six 3-inch lengths of beading wire. Cut one end of the wires in an arch leaving one side of the wires 1-5/8 inch and the other side 2 inches in length. Trim the excess tape.
STEP 3
Pass one end of the taped beading wire into a ribbon end. Place a small amount of glue (E-6000® Jewelry and Craft Adhesive) on the inside of the ribbon end (optional). Using chain-nose pliers, compress the ribbon end over the wires. Repeat to attach a ribbon end to the opposite end of the beading wires.
STEP 4
Repeat Steps 2 and 3 to make a second beading wire component.
STEP 5
String one Swarovski crystal red magma 14mm twist onto a headpin. Using a pair of chain-nose pliers, round-nose pliers and flush-cutters, form a simple loop on the straight end of the wire. Repeat to create a second Swarovski crystal red magma 14mm twist bead drop.
STEP 6
Using a pair of chain-nose pliers and flat-nose pliers, open a 4mm jumpring. Pass it through the loop on a beading wire component and one Swarovski crystal red magma 14mm twist bead drop. Close the jumpring.
STEP 7
Open the loop on an earwire. Pass it through the opposite loop on the beading wire component. Close the loop.
STEP 8
Repeat Steps 6 and 7 to create the second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You