Single-Strand Necklace and Earring Set with Swarovski Crystal, Gold-Finished "Pewter" Drops and Gold-Plated Brass Beads and Components

Necklace

STEP 1
Cut the following lengths of Accu-Flex® professional-quality beading wire:
  • One 22-inch length
  • One 10-inch length
  • One 6-inch length
  • One 4-inch length
STEP 2
Pass one 4mm jumpring through the loop on one 6mm round drop and the bottom hole in the 3-strand spacer bar (third strand) then close. Repeat to attach one 6mm round drop to the bottom hole in the remaining spacer bars.

First Strand

STEP 3
String one crimp on one end of the 4-inch length of beading wire then crimp.

String the following onto the beading wire:
  • The second hole in one 5-strand spacer bar
  • 15 jet nut 2X 3mm bicones
  • The second hole in a second one 5-strand spacer bar
  • One crimp
STEP 4
Using crimping pliers crimp the crimp bead. Finish with a 4mm crimp cover on each end.

Second Strand

STEP 5
String one crimp on one end of the 6-inch length of beading wire then crimp.

String the following onto the beading wire:
  • The second hole in one 4-strand spacer bar
  • One jet nut 2X 3mm bicone
  • Six erinite 3mm bicones
  • One jet nut 2X 3mm bicone
  • The third hole in the 5-strand spacer bar (first strand)
  • 13 jet nut 2X 3mm bicones
  • The third hole in the second 5-strand spacer bar (first strand)
  • One jet nut 2X 3mm bicone
  • Six erinite 3mm bicones
  • One jet nut 2X 3mm bicone
  • The second hole in a second 4-strand spacer bar
  • One crimp
Repeat Step 4 to secure the strand.

Third Strand

STEP 6
String one crimp on one end of the 10-inch length of beading wire then crimp.

String the following onto the beading wire:
  • The second hole in a 3-strand spacer bar
  • One jet nut 2X 3mm bicone
  • Four light grey opal 3mm bicones
  • One jet nut 2X 3mm bicone
  • The third hole in the 4-strand spacer bar (second strand)
  • One jet nut 2X 3mm bicone
  • Five erinite 3mm bicones
  • The fourth hole in the 5-strand spacer bar (first strand)
  • 11 jet nut 2X 3mm bicones
  • The fourth hole in the second 5-strand spacer bar (first strand)
  • One jet nut 2X 3mm bicone
  • Five erinite 3mm bicones
  • One jet nut 2X 3mm bicone
  • The third hole in the 4-strand second spacer bar (second strand)
  • One jet nut 2X 3mm bicone
  • Four light grey opal 3mm bicones
  • One jet nut 2X 3mm bicone
  • The second hole in a second 3-strand spacer bar
  • One crimp
Repeat Step 4 to secure the strand.

Fourth Strand

STEP 7
String onto the beading wire: one crimp and one Accu-Guard™ wire protector. Pass the beading wire back through the crimp. Pull the beading wire so the crimp rests snug against the Accu-Guard leaving approximately 1/4 inch of beading wire on the end.

Crimp, then trim the excess from the short end of the beading wire. Finish with a 3mm crimp cover.
STEP 8
String the following onto the beading wire in the pattern of your choice:
  • 20 gold-plated 3mm rounds
  • 12 jet nut 2X 3mm bicone
  • Seven gold-plated 5mm round
  • Seven erinite 6mm round
  • Six light grey opal 3mm bicone
  • Two erinite 3mm bicone
STEP 9
String Fourth Strand Through Five-Strand Spacer Bar Continue to string the following:
  • The top hole on the 3-strand spacer bar (third strand)
  • One jet nut 2X 3mm bicone
  • Three light grey opal 3mm bicones
  • One jet nut 2X 3mm bicone
  • The top hole in the 4-strand spacer bar (second strand)
  • One jet nut 2X 3mm bicone
  • Four erinite 3mm bicones
  • One jet nut 2X 3mm bicone
  • The top hole in the 5-strand spacer bar (first strand)
STEP 10
Continue to string nine jet nut 2X 3mm bicones then repeat the stringing sequence in Step 7 and 8 in the opposite direction using the top hole in the second 3-strand, 4-strand and 5-strand spacer bars to string the second half of the necklace.

Repeat Step 4 to secure the strand.
STEP 11
Pass one 4mm jumpring through the loop on one portion of the toggle clasp and the Accu-Guard on one end of the necklace then close. Repeat to attach the second portion of the clasp.

Earrings

STEP 1
String onto one 1-inch eyepin: one jet nut 2X 3mm bicone, one erinite 6mm round and one jet nut 2X 3mm bicone then form a simple loop creating an erinite link. Repeat to create a second link.
STEP 2
Pass one 4mm jumpring through one 6mm round drop and the loop on one end of one erinite link then close. Attach one leverback earwire to the opposite end of the link.

Repeat to create a second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You