Double-Strand Necklace, Bracelet and Earring Set with Egyptian Crystal and Imitation Rhodium-Finished Pewter Spacer Bars and Swarovski Crystal

Necklace

STEP 1
Using flush-cutters cut the following:
  • One 20-inch length of Accu-Flex® professional-quality beading wire
  • One 24-inch length of Accu-Flex
STEP 2
Onto one 1-1/2 inch silver plated eyepin string the following:
  • The first hole of one clear AB 12x4mm 2-strand spacer bar
  • The second hole of one 12x4mm 2-strand spacer bar
  • The first hole of one 12x4mm 2-strand spacer bar
Using a pair of chain-nose pliers, round-nose pliers and flush-cutters form a simple loop on the straight end of the wire.
STEP 3
Onto one eyepin string the following:
  • The second hole of the first 12x4mm 2-strand spacer bar in Step 2
  • The first hole of one 12x4mm 2-strand spacer bar
  • The second hole of the second 12x4mm 2-strand spacer bar
Form a simple loop.

Onto one eyepin string the following:
  • The first hole of one 12x4mm 2-strand spacer bar
  • The second hole of the 12x4mm 2-strand spacer bar previously added
  • The first hole of one 12x4mm 2-strand spacer bar
Form a simple loop.

Repeat seven more times.
STEP 4
Onto one eyepin string the following:
  • The second hole of the last outside 12x4mm 2-strand spacer bar added in Step 3
  • The first hole of one clear AB 18x3mm 3-strand spacer bar
  • The second hole of the last inside 12x4mm 2-strand spacer bar added in Step 3
Form a simple loop.
STEP 5
Onto one eyepin string the following:
  • One gold-plated 3x1mm bead-cap (concave side first)
  • The first hole of one 18x3mm 3-strand spacer bar
  • One Swarovski 4mm Tahitian pearl
  • The second hole of the 18x3mm 3-strand spacer bar added in Step 4
  • One 4mm Tahitian pearl
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 3x1mm bead-cap (convex side first)
Form a simple loop.
STEP 6
Onto one eyepin string the following:
  • One 3x1mm bead cap (concave side first)
  • The second hole of the first 18x3mm 3-strand spacer bar added in Step 5
  • One 4mm iridescent green bicone
  • The third hole of the 18x3mm 3-strand spacer bar added in Step 4
  • One 4mm iridescent green bicone
  • The second hole of the second 18x3mm 3-strand spacer bar added in Step 5
  • One 3x1mm bead cap (convex side first)
Form a simple loop.
STEP 7
Onto one eyepin string the following:
  • One 3x1mm bead cap (concave side first)
  • The third hole of the first 18x3mm 3-strand spacer bar added in Step 5
  • One 4mm iridescent green bicone
  • The first hole of one clear AB 18x3mm 3-strand spacer bar
  • One 4mm Tahitian pearl
  • The first hole of one clear AB 18x3mm 3-strand spacer bar
  • One 4mm Tahitian pearl
  • The first hole of one 18x3mm spacer bar
  • One 4mm iridescent green bicone
  • The third hole of the last 18x3mm 3-strand spacer bar added in Step 5
  • One 3x1mm bead cap (convex side first)
Form a simple loop.
STEP 8
On one eyepin string the following:
  • One 3x1mm bead cap (concave side first)
  • The third hole of the first 18x3mm spacer bar added in Step 7
  • One 4mm iridescent green bicone
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 4mm Tahitian pearl
  • The third hole of the second 18x3mm 3-strand spacer bar added in Step 7
  • One 4mm Tahitian pearl
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 4mm iridescent green bicone
  • The third hole of the third 18x3mm 3-strand spacer bar added in Step 7
  • One 3x1mm bead cap (convex side first)
Form a simple loop.
STEP 9
Repeat Steps 7 and 8.

Your spacer bar chain now has three 18x3mm spacer bars in the center row; two are attached through two holes, and the last is attached through only the first hole.
STEP 10
Repeat Step 7, adding 20x3mm 3-strand spacer bars in place of 18x3mm 3-strand spacer bars.

Repeat Step 8, adding 20x3mm 3-strand spacer bars in place of 18x3mm 3-strand spacer bars.

Repeat Step 7 again, adding 20x3mm 3-strand spacer bars in place of 18x3mm 3-strand spacer bars.
STEP 11
On one eyepin string the following:
  • One 3x1mm bead cap (concave side first)
  • The third hole of the last outside 20x3mm 3-strand spacer bar added
  • Two 4mm iridescent green bicones
  • The third hole of the last center 20x3mm 3-strand spacer bar added
  • Two 4mm iridescent green bicones
  • The third hole of the last inside 20x3mm 3-strand spacer bar added
  • One 3x1mm bead cap (convex side first)
Form a simple loop.
STEP 12
Repeat Steps 1-11 to create a second spacer bar chain.
STEP 13
Using a pair of chain-nose pliers and bent-nose pliers, open two silver-plated 8mm jumprings. Pass one jumpring through the first hole of the first 12x4mm 2-strand spacer bar of the first spacer bar chain and through the loop on one half of a 15mm crystal magnetic clasp. Close the jumpring.
STEP 14
String onto the 20-inch length of beading wire one sterling silver 2x2mm crimp bead. Pass the beading wire through the space between the last inner 20x3mm spacer bar and the last center 20x3mm spacer bar of the first spacer bar chain. Pass the beading wire back through the crimp bead. Pull the beading wire so the crimp rest against the bicones between the spacer bars. Place a small amount of adhesive (Loctite®) inside the crimp (optional).

Using crimping pliers, crimp the crimp bead. Using flush cutters trim the excess from the short end of the beading wire. Place one silver-plated 4mm crimp cover over the crimp bead then gently close it.
STEP 15
Onto the beading wire string three Swarovski 8mm light grey pearls and one Swarovski 4mm iridescent green bicone. Repeat for a total of 13 sets.

Continue by stringing three 8mm light grey pearls.
STEP 16
Repeat Step 14 to attach the beading wire to the second spacer bar chain.
STEP 17
String onto the 24-inch length of beading wire one sterling silver 2x2mm crimp bead. Pass the beading wire through the space between the last outer 20x3mm spacer bar and the last center 20x3mm spacer bar of the first spacer bar chain. Pass the beading wire back through the crimp bead. Pull the beading wire so the crimp rest against the bicones between the spacer bars. Place a small amount of adhesive (Loctite) inside the crimp (optional).

Using crimping pliers, crimp the crimp bead. Using flush cutters trim the excess from the short end of the beading wire. Place one silver-plated 4mm crimp cover over the crimp bead then gently close it.
STEP 18
On the beading wire string three 8mm light grey pearls and one 4mm iridescent green bicone. Repeat for a total of 14 sets.

Continue by stringing three 8mm light grey pearls.
STEP 19
Repeat Step 17 to connect the beading wire to the second spacer bar chain.
STEP 20
Pass one jumpring through the first hole of the first 12x4mm 2-strand spacer bar on the second spacer bar chain and through the loop on the second half of a rhodium-finished and crystal magnetic clasp. Close the jumpring.

Bracelet

STEP 1
Using chain-nose pliers and bent-nose pliers open two silver-plated 8mm jumprings and two silver-plated 6mm jumprings.
STEP 2
Using flush cutters, remove the prongs of one 17x10mm swan charm. Using nylon jaw pliers, close the bail. Thread one 6mm jumpring through the loop of the bail. Close the jumpring.
STEP 3
Onto on 8mm jumpring, thread the loop of one half of a 15mm crystal magnetic clasp and the first hole of one 12x4mm 2-strand spacer bar. Close the jumpring.
STEP 4
Onto one 1-1/2 inch silver-plated eyepin string the following:
  • The first hole of one 12x4mm 2-strand spacer bar
  • The second hole of the spacer bar added in Step 3
  • The first hole of one 12x4mm 2-strand spacer bar
Using chain-nose pliers, round-nose pliers and flush cutters, form a simple loop.
STEP 5
Onto one eyepin string the following:
  • The second hole of the first 2-strand spacer bar added in Step 4
  • The first hole of one 18x3mm 3-strand spacer bar
  • The second hole of the second 2-strand spacer bar added in Step 4
Form a simple loop.
STEP 6
Onto one eyepin string the following:
  • One gold-plated 3x1mm bead cap (concave side first)
  • The first hole of one 18x3mm 3-strand spacer bar
  • One Swarovski 4mm Tahitian pearl
  • The second hole of the 18x3mm 3-strand spacer bar added in Step 5
  • One 4mm Tahitian pearl
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 3x1mm bead cap (convex side firsts)
Form a simple loop.
STEP 7
Onto one eyepin string the following:
  • One 3x1mm bead cap (concave side first)
  • The second hole of the first 18x3mm 3-strand spacer bar added in Step 6
  • One Swarovski 4mm iridescent green bicone
  • The third hole of the 18x3mm 3-strand spacer bar added in Step 5
  • The second hole of the second 18x3mm spacer bar added in Step 6
  • One 3x1mm bead cap (convex side first)
Form a simple loop.
STEP 8
Onto one eyepin string the following:
  • One 3x1mm bead cap (concave side first)
  • The third hole of the first 18x3mm spacer bar added in Step 7
  • One 4mm iridescent green bicone
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 4mm Tahitian pearl
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 4mm Tahitian pearl
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 4mm iridescent green bicone
  • The third hole of the second 18x3mm spacer bar added in Step 7
  • One 3x1mm bead cap (convex side first)
Form a simple loop.
STEP 9
On one eyepin string the following:
  • One 3x1mm bead cap (concave side first)
  • The third hole of the first 18x3mm 3-strand spacer bar added in Step 8
  • One 4mm iridescent green bicone
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 4mm Tahitian pearl
  • The third hole of the second 18x3mm 3-strand spacer bar added in Step 8
  • One 4mm Tahitian pearl
  • The first hole of one 18x3mm 3-strand spacer bar
  • One 4mm iridescent green bicone
  • The third hole of the third 18x3mm spacer bar added in Step 8
  • One 3x1mm bead cap (convex side first)
Form a simple loop.
STEP 10
Repeat Step 8.

Repeat Step 9, adding 20x3mm 3-strand spacer bars to the bracelet.

Repeat Step 8, adding 20x3mm 3-strand spacer bars to the bracelet.
STEP 11
Repeat Step 9, adding 20x3mm 3-strand spacer bars to the bracelet.
STEP 12
Repeat Steps 3 - 10 in reverse to finish the second half of the bracelet.
STEP 13
Thread one 6mm jumpring through the jumpring attached to the swan bail and one simple loop on the bracelet. Close the jumpring.

Earrings

STEP 1
Mix Devcon® 5 Minute® Epoxy according to manufacturer’s instructions. Place a thin layer of adhesive on the inside the cup of one silver-finished earstud with loop and on the back of one Swarovski 8x6mm faceted fancy oval stone. Press the stone into the mounting. Let the adhesive set for 5 minutes. Repeat to set a stone in the second earstud.
STEP 2
Using flush-cutters cut two 1-3/4 inch lengths and two 1-1/4 inch lengths of 12 gauge textured aluminum wire.

Using chain-nose pliers and bent-nose pliers, open two stainless steel 5mm jumprings.
STEP 3
Using Wubbers® Designer Mandrel large bail-making pliers (the 9mm side of the jaw), nylon-jaw pliers and one 1-1/4 inch length of wire, create a ring. Repeat to create a second ring.

Using Wubbers Designer Mandrel large half-round pliers (the 12mm side of the jaw), nylon-jaw pliers and one 1-3/4 inch length of wire, create a D-ring. Repeat to create a second D-ring.

Using nylon-jaw pliers, open all four aluminum wire jumprings.
STEP 4
On one D-ring, thread the first hole of two 12x4mm 2-strand spacer bars. Close the ring.
STEP 5
On one eyepin string the following:
  • The second hole of the first 2-strand spacer bar added in Step 4
  • The first hole of one 12x4mm 2-strand spacer bar
  • The second hole of the second 2-strand spacer bar added in Step 4
Using chain-nose pliers, round-nose pliers and flush-cutters, form a simple loop.
STEP 6
On one eyepin string the following:
  • The first hole of one 12x4mm 2-strand spacer bar
  • The second hole of the 2-strand spacer bar added in Step 5
  • The first hole of one 12x4mm 2-strand spacer bar
Form a simple loop.
STEP 7
Repeat Step 5.
STEP 8
Onto one round ring created in Step 3 string the second hole of the 2-strand spacer bar added in Step 7. Close the ring.

Onto one 5mm jumpring string the aluminum ring and the loop of one earstud. Close the jumpring.
STEP 9
Repeat Steps 4-8 to complete the second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You