Multi-Strand Necklace and Earring Set with Swarovski® Crystals and 14Kt Gold-Filled Beads

Necklace

STEP 1
Cut two 1-1/2 inch length 1.25mm cable chain and seven 25-inch lengths Accu-Flex professional-quality beading wire.
STEP 2
Pass one 6mm jumpring through the loop on one crystal clear 31.5mm pure drop and the first hole on one luminous green 14mm square sew-on then close. Attach one 6mm jumpring to the opposite end of the 14mm square sew-on creating a square sew-on and 31.5mm pure drop. Repeat to create a total of two creating a square sew-on and 31.5mm pure drops.

Repeat to create one square sew-on and 44mm pure drop.
STEP 3
Use on 6mm jumpring to attach one 21mm to the first hole on one luminous green 14mm square sew-on then use a 5mm jumpring to attach the first link on one 1-1/2 inch length of chain to the hole on the opposite end square sew-on and 21mm pure drop. Attach a 5mm to the last link on the chain.

Repeat to create a total of two creating a square sew-on and 21mm pure drops.

Attach one 5mm jumpring to each of the remaining six 31.5mm and two 44mm pure drops.

First, Third, Fourth and Sixth Strands

STEP 4
String onto one length of beading wire: one crimp and one Accu-Guard™ wire protector. Pass the beading wire back through the crimp. Pull the beading wire so the crimp rests snug against the Accu-Guard leaving approximately 1/4 inch of beading wire on the end.

Crimp then trim the excess from the short end of the beading wire.
STEP 5
String 25 17.5x1mm spiral tubes onto the beading wire then repeat Step 4 to secure the strand.
STEP 6
Repeat Steps 4 and 5 to create a total of four strands.

Second Strand

STEP 7
Repeat Step 4 to begin the second strand.

String the following onto the beading wire:
  • One luminous green 3mm bicone
  • One crystal AB 6mm globe
  • Two luminous green 3mm bicones
  • One crystal AB 6mm globe
Repeat to string a total of 24 sets then repeat Step 4 to secure the strand.

Fifth Strand

STEP 8
Repeat Step 4 to begin the fifth strand.

String the following onto the beading wire:
  • Two crystal AB2X 3mm bicones
  • One luminous green 6mm globe
  • Three crystal AB2X 3mm bicones
  • One crystal AB 6mm globe
Repeat to string a total of 19 sets then string two crystal AB2X 3mm bicones. Repeat Step 4 to secure the strand.

Seventh Strand

STEP 9
Repeat Step 4 to begin the fifth strand.

Repeat this sequence to string three sets:
  • 34 luminous green 4mm rounds
  • Repeat this sequence to string three sets:
    • The 5mm jumpring on one 31.5mm pure drop
    • Four luminous green 4mm rounds
  • The 5mm jumpring on one 44mm pure drop
  • Four luminous green 4mm rounds
  • The 6mm jumpring on one square sew-on and 31.5mm pure drop
  • Two luminous green 4mm rounds
  • The 5mm jumpring on one square sew-on and 21mm pure drop
  • Two luminous green 4mm rounds
STEP 10
Continue to string the 6mm jumpring on one square sew-on and 44mm pure drop then repeat Step 9 in the opposite order to string the second half of the necklace. Repeat Step 4 to secure the strand.
STEP 11
Pass one 5mm jumpring through the Accu-Guard on one end of the first strand and the top loop on one portion of the 5-strand slide lock clasp then close. Repeat to attach the second through seventh strands to the next loop on same portion of the clasp.

Repeat to attach the opposite end of each strand to the second portion of the clasp.

Earrings

STEP 1
Cut four 6-inch lengths of beading wire.
STEP 2
Attach one 5mm jumpring to each of the one 44mm, one 31.5mm and two 21mm pure drops.
STEP 3
String onto one length of beading wire: one crimp, one Accu-Guard™ wire protector and the 5mm jumpring attached to one 21mm pure drop.
STEP 4
Pass the beading wire back through the crimp. Pull the beading wire so the crimp rests snug against the Accu-Guard leaving approximately 1/4 inch of beading wire on the end.

Crimp then trim the excess from the short end of the beading wire.
STEP 5
String the following onto the beading wire: one 17.5x1mm spiral tube, one crimp and one Accu-Guard™ wire protector then repeat Step 4 to secure.
STEP 6
Repeat Steps 3 - 5 to create a total of two tube bead and 21mm pure drops.
STEP 7
String onto one length of beading wire: one crimp, one Accu-Guard™ wire protector and the 5mm jumpring attached to one 31.5mm pure drop.
STEP 8
Pass the beading wire back through the crimp. Pull the beading wire so the crimp rests snug against the Accu-Guard leaving approximately 1/4 inch of beading wire on the end.

Crimp then trim the excess from the short end of the beading wire.
STEP 9
String the following onto the beading wire: two 17.5x1mm spiral tubes, one crimp and one Accu-Guard™ wire protector then repeat Step 7 to secure.
STEP 10
Repeat Steps 7 - 9 to create a total of two tube bead and 31.5mm pure drops.
STEP 11
Pass one 5mm jumpring through the Accu-Guard on the end of one tube bead and 21mm pure drop, one tube bead and 31.5mm pure drop and the loop on one angular fishhook earwire then close.
STEP 12
Repeat Steps 3 - 11 to create a second earring using the remaining 21mm pure drop and 44mm pure drop.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You