Convertible Necklace, Bracelet and Earring Set with Swarovski Crystal, Cultured Freshwater Pearls and Gold-Plated Brass Beads

Necklace

STEP 1
Cut the following:
  • Accu-Flex® professional-quality beading wire:
    • One 20-inch length
    • One 17-inch length
    • One 16-inch length
    • One 14-inch length
    • One 13-inch length
    • One 11-inch length
    • One 9-inch length
  • 2mm Figaro chain:
    • One 1/2 inch length
    • One 1-inch length
    • One 1-1/2 length

Fancy Stone Clasp

STEP 2
Mix Devcon® 5-Minute® Epoxy according to manufacturer's instructions

Apply a thin layer of epoxy inside the bezel setting of one 13x11mm oval clasp and the back of one jet 8x6mm oval fancy stone. Press the fancy stone into the setting. Let the adhesive set for 5 minutes. Make sure to use proper ventilation when using this product.

Infinity Pendant

STEP 3
Pass one 8mm twisted jumpring through the first link on one 1/2 inch length of Figaro chain and the smaller loop on one silver night 18mm infinity drop then close.

Repeat to attach one infinity drop to the first link on the 1-inch and 1-1/2 inch lengths of chain.
STEP 4
Pass one 4mm jumpring through the last link on each length of chain and the loop on one lobster claw clasp then close.
STEP 5
Attach one 4mm jumpring to 13 lobster claw clasps.

6-1/2 inch Swag/Bracelet

STEP 6
Swag Bracelet Strand String onto the 9-inch length of beading wire: one crimp and the jumpring on one lobster claw clasp. Pass the beading wire back through the crimp. Pull the beading wire so the crimp rests snug against the jumpring leaving approximately 1/4 inch of beading wire on the end.

Crimp, then trim the excess from the short end of the beading wire. Finish with a 4mm crimp cover.
STEP 7
String the following onto the beading wire:
  • 15 blush rose 3mm bicones
  • One copper 6-7mm button pearl
  • 30 metallic sunshine 3mm bicones
  • One copper 6-7mm button pearl
  • 15 blush rose 3mm bicones
Repeat Step 4 to secure the strand.

7-3/4 inch Swag

STEP 8
Repeat Step 4 using the 11-inch length of beading wire.

String the following onto the beading wire:
  • 19 blush rose 3mm bicones
  • One copper 6-7mm button pearl
  • 38 metallic sunshine 3mm bicones
  • One copper 6-7mm button pearl
  • 19 blush rose 3mm bicones
Repeat Step 4 to secure the strand.

9-1/2 inch Swag

STEP 9
Repeat Step 4 using the 13-inch length of beading wire.

String the following onto the beading wire:
  • 16 blush rose 4mm bicones
  • One copper 6-7mm button pearl
  • 28 metallic sunshine 4mm bicones
  • One copper 6-7mm button pearl
  • 16 blush rose 4mm bicones
Repeat Step 4 to secure the strand.

11-3/4 inch Swag

STEP 10
Repeat Step 4 using the 14-inch length of beading wire.

String the following onto the beading wire:
  • 20 blush rose 4mm bicones
  • One copper 6-7mm button pearl
  • 33 metallic sunshine 4mm bicones
  • One copper 6-7mm button pearl
  • 20 blush rose 4mm bicones
Repeat Step 4 to secure the strand.

12-1/2 inch Swag

STEP 11
Repeat Step 4 using the 16-inch length of beading wire.

String the following onto the beading wire:
  • 16 blush rose 6mm bicones
  • One copper 6-7mm button pearl
  • 24 metallic sunshine 6mm bicones
  • One copper 6-7mm button pearl
  • 16 blush rose 6mm bicones
Repeat Step 4 to secure the strand.

14-3/4 inch Swag

STEP 12
Repeat Step 4 using the 17-inch length of beading wire.

String the following onto the beading wire:
  • 19 blush rose 6mm bicones
  • One copper 6-7mm button pearl
  • 28 metallic sunshine 6mm bicones
  • One copper 6-7mm button pearl
  • 19 blush rose 6mm bicones
Repeat Step 4 to secure the strand.

Necklace Assembly

STEP 13
String onto the 20-inch length of beading wire: one crimp and one Accu-Guard wire protector. Pass the beading wire back through the crimp. Pull the beading wire so the crimp rests snug against the Accu-Guard leaving approximately 1/4 inch of beading wire on the end.

Crimp, then trim the excess from the short end of the beading wire. Finish with a 4mm crimp cover.
STEP 14
String the following onto the beading wire:
  • One 3x1mm ribbed round bead cap
  • One metallic sunshine 6mm round
  • One 3x1mm ribbed round bead cap
  • One 4x2mm coil
  • One 3x1mm ribbed round bead cap
  • One blush rose 6x4mm rondelle
  • One 3x1mm ribbed round bead cap
  • One 4x2mm coil
Repeat this sequence to string a total of 11 sets.
STEP 15
Continue to string the following:
  • One 3x1mm ribbed round bead cap
  • One blush rose 6x4mm rondelle
  • One 3x1mm ribbed round bead cap
  • One 4x2mm coil
Repeat the sequence in Step 12 to string ten more sets then string one 3x1mm ribbed round bead cap, one metallic sunshine 6mm round and one 3x1mm ribbed round bead cap.

Repeat Step 11 to secure the strand.

Tip: The swag strands and pendant can be attached to the necklace strand in multiple ways for several versatile looks.

Earrings

STEP 1
Mix a small amount of Devcon® 5 Minute® Epoxy according to manufacturer's instructions.

Apply a small amount of epoxy to the center of the bezel on one 14mm fishhook earwire and the back of one jet 3.8mm flat back. Press the flat back in the bezel to secure it in place.

Repeat to attach a flat back to the second earwire then set them aside to dry for approximately 5 minutes.
STEP 2
String one blush rose 3mm bicone onto one 1-inch headpin then form a simple loop. Repeat to create a total of 16 blush rose bicone drops.

Repeat to create 16 metallic sunshine 3mm bicone drops.
STEP 3
Pass one 8mm twisted jumpring through the smaller loop on one silver night 18mm infinity drop and one 4mm jumpring then close.

Continue to connect a total of seven 4mm jumprings creating a chain. Pass one 4mm jumpring through the loop on the fishhook earwire and the last jumpring on the chain then close.
STEP 4
Attach eight blush rose bicone drops and eight metallic sunshine bicone drops to the jumpring chain.
STEP 5
Repeat Steps 2 - 4 to create a second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You