Two-Piece Necklace, Bracelet and Earring Set with Swarovski Crystal and Dione® Large-Hole Beads

Necklace A

STEP 1
Mix Devcon® 5 Minute® Epoxy according to the manufacturer's instructions. Place a thin layer of adhesive on the back of one Swarovski jet 32x17mm fancy marquise stone and a small amount on the inside of one gold-plated 34x19mm marquise mount. Press the stone into the setting. Set aside and allow to cure completely.

Repeat to create a total of four jet fancy stone pendants and three golden shadow fancy stone pendants.
STEP 2
Using chain-nose pliers and bent-nose pliers open nine gold-plated 5.5mm jumprings (two of these jumprings will be used in Step 3).

Pass one jumpring through the loop of one marquise pendant and the loop of one gold-finished and rhinestone rondelle. Close jumpring.

Repeat with the six remaining marquise pendants and rondelles.
STEP 3
Using chain-nose pliers and bent-nose pliers separate two 6-1/4 inch lengths (8 links) of gold-plated Swarovski jet rivoli chain. Pass one 5.5mm jumpring through the loop of the first link on one length of rivoli chain and the loop on the bar portion of one gold-plated 16mm toggle clasp. Close the jumpring.

Pass one 5.5mm jumpring through the loop of the first link on the second length of rivoli chain and the loop on the ring portion of the toggle clasp. Close the jumpring.
STEP 4
Using flush cutters cut one 8-1/2 inch length of Accu-Flex® professional-quality beading wire.

String onto the beading wire one gold-filled 2x2mm crimp bead, one gold-plated Accu-Guard™ wire protector and the loop on the last link of one length of rivoli chain. Pass the beading wire back through the crimp bead. Pull the beading wire so the crimp rests snug against the Accu-Guard. Place a small amount of adhesive (Loctite®) inside the crimp (optional).

Using crimping pliers crimp the crimp bead. Using flush-cutters trim the excess from the short end of the beading wire.
STEP 5
String the following pattern onto the beading wire seven times:
  • One Swarovski light Colorado topaz 10mm round
  • One gold-plated 11x4mm bead cap
  • One rhinestone rondelle and Swarovski marquise pendant
  • One gold-plated 11x4mm bead cap
Finish the pattern with one Swarovski light Colorado topaz 10mm round.
STEP 6
String onto the beading wire one gold-filled 2x2mm crimp bead, one gold-plated Accu-Guard wire protector and the loop on the last link of the second length of rivoli chain. Pass the beading wire back through the crimp bead. Pull the beading wire so the crimp rests snug against the Accu-Guard. Place a small amount of adhesive (Loctite) inside the crimp (optional).

Using crimping pliers crimp the crimp bead. Using flush-cutters trim the excess from the short end of the beading wire.

Necklace B

STEP 1
Using chain-nose pliers and bent-nose pliers separate one 36-inch length of gold-plated Swarovski jet rivoli chain (48 links).
STEP 2
Using chain-nose pliers and bent-nose pliers open two gold-plated 5.5mm jumprings. Pass one jumpring through the loop on the first link of the rivoli chain length and the loop of one gold-plated swivel lobster claw clasp. Close the jumpring.

Repeat on the opposite end of the necklace with a second lobster claw clasp.

Bracelet

STEP 1
Mix Devcon 5 Minute Epoxy according to the manufacturer's instructions. Place a thin layer of adhesive on the back of one Swarovski jet 32x17mm fancy marquise stone and a small amount on the inside of one gold-plated 34x19mm marquise mount. Press the stone into the setting. Set aside and allow to cure completely.
STEP 2
Using flush-cutters cut two 7-inch lengths of gold-plated Swarovski jet rivoli chain (9 links each).
STEP 3
Using chain-nose and bent-nose pliers open five gold-plated 5.5mm jumprings.
STEP 4
Pass one open jumpring through the loop on the first link on one length of rivoli chain and the loop on the bar portion of one gold-plated 16mm toggle clasp. Close the jumpring.

Pass one open jumpring through the loop on the last link of the rivoli chain and the loop on the ring portion of the toggle clasp. Close the jumpring.

Repeat with the second length of chain.
STEP 5
Pass one open jumpring through the loop of the Swarovski marquise pendant created in Step 1 and the ring portion of the toggle clasp. Close the jumpring.

Earrings

STEP 1
Mix Devcon 5 Minute Epoxy according to the manufacturer's instructions. Place a thin layer of adhesive on the back of one Swarovski jet 32x17mm fancy marquise stone and a small amount on the inside of one gold-plated 34x19mm marquise mount. Press the stone into the setting. Set aside and allow to cure completely.

Repeat to set a second stone.
STEP 2
Using chain-nose pliers and bent-nose pliers separate two single links of gold-plated Swarovski jet rivoli chain. Be sure to keep the jumpring from the chain on one loop of each link.
STEP 3
Using chain-nose pliers and bent-nose pliers, open the oval jumpring on one rivoli link. Pass the jumpring through the loop of the marquise pendant. Close the jumpring.
STEP 4
Open the loop on one gold-plated 15mm leverback earwire. Pass the loop through the loop of one rivoli link. Close the loop.
STEP 5
Repeat Steps 3 and 4 to complete the second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You