Three-Piece Necklace, Earrings and Bracelet Set with Swarovski Crystal and Gold-Plated Brass Focals and Gold-Plated Pewter Drops and Links


For more inspiration, read this informative article ...

Get ready to FLASH people with a jewelry parure that's simply stunning from all angles. Take the guesswork out of layering jewelry with three necklaces that are expertly designed to be worn together for a beautifully balanced look. These necklaces can also be worn individually for an entirely different style, offering a ...

First Necklace

STEP 1
Mix Araldite® Standard Epoxy according to manufacturer's instructions. Place a thin layer of adhesive on the inside of one gold-plated 32x25mm pear setting and the back of one Swarovski crystal vitrail medium 30x20mm pear fancy stone. Press the stone into the setting creating one Swarovski fancy stone focal. Let the adhesive set for 90 minutes. Make sure to use proper ventilation when using this product. Repeat to create a total of three fancy stone focals.
STEP 2
Cut two 3-inch lengths of gold-finished rolo chain and one 11-1/2 inch length of Accu-Flex® professional-quality beading wire.
STEP 3
Pass one 7mm jumpring through first link of one 3-inch length of chain then close.
STEP 4
Pass one 4.5mm jumpring through the first link of the second length of chain and the loop of one gold-plated lobster claw clasp then close. Repeat to attach a second jumpring creating double jumprings.
STEP 5
String onto the beading wire, one sterling silver 2x2mm crimp bead, one Accu-Guard™ wire protector and link on the opposite end of one length of chain. Pass the beading wire back through the crimp bead. Pull the beading wire so the crimp rests snug against the Accu-Guard, leaving approximately 1/4 inch of beading wire on the end. Place a small amount of adhesive (Loctite®) inside the crimp (optional).

Crimp the crimp bead then trim the excess from the short end of the beading wire. Finish with a 4mm crimp cover.
STEP 6
String the following onto the beading wire:
  • Five Swarovski dark moss green 6mm rondelles
  • One gold-plated Swarovski crystal AB 6mm rondelle
  • Seven Swarovski lilac shadow 8mm rondelles
  • One gold-plated Swarovski crystal AB 6mm rondelle
  • Five Swarovski dark moss green 8mm rondelles
  • One gold-plated Swarovski crystal AB 6mm rondelle
STEP 7
Continue to string onto the beading wire seven Swarovski lilac shadow 8mm rondelles.
STEP 8
Repeat the stringing sequence in Step 6 in the opposite direction to string the second half of the necklace then repeat Step 5 using the second length of chain.

Second Necklace

STEP 1
Cut two 3-inch sections of gold-finished rolo chain and one 11-1/2 inch length of beading wire..
STEP 2
Pass the 7mm jumpring through the first link on one length of chain then close.
STEP 3
Pass one 4.5mm jumpring through the last link of the second chain and the loop of one gold-plated lobster claw clasp then close. Repeat to attach a second jumpring creating double jumprings.
STEP 4
String onto the beading wire, one sterling silver 2x2mm crimp bead, one Accu-Guard wire protector and the last link on one length of chain. Pass the beading wire back through the crimp bead. Pull the beading wire so the crimp rests snug against the Accu-Guard, leaving approximately 1/4 inch of beading wire on the end. Place a small amount of adhesive (Loctite®) inside the crimp (optional).

Crimp the crimp bead then trim the excess from the short end of the beading wire. Finish with a 4mm crimp cover.
STEP 5
String the following onto the beading wire:
  • Five Swarovski dark moss 6mm rondelles
  • Forty Swarovski dark moss 8mm rondelles
  • Five Swarovski dark moss 6mm rondelles
STEP 6
Repeat Step 4 using the second length of chain.

Third Necklace

STEP 1
String the following onto one 2-inch eyepin:
  • One Swarovski dark moss 8mm rondelle
  • One gold-plated Swarovski crystal AB rondelle
  • One Swarovski lilac shadow bicone
Form a wrapped loop on the straight end of the wire.

Repeat to create a total of three beaded links.
STEP 2
Open the eyepin loop on one beaded link. Pass the loop through the loop of one Swarovski pear focal then close.

Repeat to connect a total of three links and focals.
STEP 3
Cut two 3-1/4 inch sections of gold-finished rolo chain and one 14-inch length of beading wire.
STEP 4
Pass the 7mm jumpring through the end of one length of chain then close.
STEP 5
Pass one 4.5mm jumpring through the last link of the second chain and the loop of one lobster claw clasp then close. Repeat to create double jumprings.
STEP 6
String onto the beading wire, one sterling silver 2x2mm crimp bead, one Accu-Guard and the last link on one chain. Pass the beading wire back through the crimp bead. Pull the beading wire so the crimp rests snug against the Accu-Guard, leaving approximately 1/4 inch of beading wire on the end. Place a small amount of adhesive (Loctite) inside the crimp (optional).

Crimp the crimp bead then trim the excess from the short end of the beading wire. Finish with a 4mm crimp cover.
STEP 7
String the following onto the beading wire:
  • Seven Swarovski dark moss 6mm rondelles
  • Fourteen Swarovski dark moss 8mm rondelles
  • One gold-plated Swarovski crystal AB 6mm rondelle
  • One Swarovski lilac shadow 8mm rondelle
  • One gold-plated Swarovski crystal AB 6mm rondelle
  • One Swarovski dark moss 8mm rondelle
  • One Swarovski fancy pear drop created in Step 3
  • One Swarovski dark moss 8mm rondelle
  • One gold-plated Swarovski crystal AB 6mm rondelle
  • One Swarovski lilac shadow 8mm rondelle
  • One gold-plated Swarovski crystal AB 6mm rondelle
STEP 8
Continue to string the following onto the beading wire:
  • One Swarovski dark moss 8mm rondelle
  • One Swarovski fancy pear drop
  • One Swarovski dark moss 8mm rondelle
STEP 9
Repeat the sequence in Step 7 in the opposite direction to string the second half of the necklace then repeat Step 6 using the second length of chain.

Bracelet

STEP 1
Mix Araldite according to manufacturer's instructions. Place a thin layer of adhesive ton the back of one Swarovski vitrail medium 18mm rivoli and a small amount on the inside of one gold-plated 18mm rivoli link setting.

Press the stone into the setting creating a rivoli drop. Let the adhesive set for 90 minutes. Make sure to use proper ventilation when using this product.

Repeat to set a total of five rivoli drops.
STEP 2
Cut one 2-inch length of gold-plated Figaro chain.
STEP 3
Pass one 5mm jumpring through the loop of one gold-plated rivoli link setting and the last link of the length of chain then close. Repeat to create double jumprings.
STEP 4
Pass one jumpring through the opposite loop of the rivoli link setting and first loop of a second rivoli link setting then close. Repeat to create double jumprings.

Repeat to connect a total of five links end to end.
STEP 5
Pass one jumpring through the loop of the last rivoli link added and through the loop of one claw clasp then close. Repeat to create double jumprings.

Earrings

STEP 1
Mix Araldite according to manufacturer's instructions. Place a thin layer of adhesive ton the back of one Swarovski vitrail medium 18mm rivoli and a small amount on the inside of one gold-plated 18mm rivoli link setting.

Press the stone into the setting creating a rivoli link. Let the adhesive set for 90 minutes. Make sure to use proper ventilation when using this product.

Repeat to create a second rivoli link.
STEP 2
String the following onto one 2-1/2 inch headpin:
  • One Swarovski lilac shadow 8mm rondelle
  • One gold-plated Swarovski crystal AB 6mm rondelle
  • One Swarovski dark moss 6mm rondelle
Form a wrapped loop on the straight end of the wire creating a beaded drop.

Repeat to create a second beaded drop.
STEP 3
Pass one 5mm jumpring through the loop on one drop and the loop on one rivoli link then close.
STEP 4
Pass the loop on one leverback earwire through the opposite loop on the rivoli link then close.
STEP 5
Repeat Steps 3 and 4 to create a second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You