Design Idea AA01
Glittery Nights
-- Designer --
Maura, Exclusively for Fire Mountain Gems and Beads®
: : : Materials : : :
Please take the creative opportunity to select the products of your choice for this design, offered here at Fire Mountain Gems and Beads.
Instructions
Using a pair of chain-nose pliers and flat-nose pliers, open a jumpring. Pass the open jumpring through a loop on one end of the clasp. Close the jumpring. Repeat to attach two jumprings to each of the loops on the first side of the clasp and then two jumprings to each of the loops on the opposite side of the clasp.
Using the flush-cutters, cut a 12-inch length of beading wire.
String onto the wire one crimp tube, a 1/2 inch piece of French wire and the first jumpring attached to the first loop on one half or the clasp. Pass the wire back through the crimp leaving one end of the wire approximately 1-inch long. Pull the crimp tight against the French wire and the jumpring so the French wire is shaped into a nicely curved tube. Place a small amount of gel adhesive inside the crimp (optional). Using the crimping pliers, crimp the crimp tube. Using flush-cutters, trim excess wire from the short end.
String onto the beading wire components to equal the length of your bracelet, minus the size of the clasp. You can follow the pattern in the finished design or create your own.
Repeat Step 3 to attach the second half of this strand to the jumpring on the second half of the clasp that matches up with the first half.
Cut one 12-inch length of Accu-Flex® beading wire. Repeat Step 3 to attach the wire to the second jumpring on the first loop on the first half of the clasp.
Repeat Step 4.
Repeat Step 3 to attach the strand to the second jumpring attached to the first loop on the second half of the clasp.
Cut one 12-inch length of Accu-Flex® beading wire. Repeat Step 3 to attach the wire to the first jumpring on the second loop on the first half of the clasp.
String onto the beading wire about 1-inch of components.
Repeat Step 3 to attach the strand to the first hole on a 29x13mm flat back divine rock. Trim the excess wire from the end.
Repeat Step 3 to attach the excess wire to the opposite hole on the 29x13mm flat back divine rock.
String onto the beading wire enough components to equal the remaining length of the bracelet.
Repeat Step 3 to attach the strand to the first jumpring attached to the second loop on the second half of the clasp.
Cut one 12-inch length of Accu-Flex® beading wire. Repeat Step 3 to attach the wire to the second jumpring on the second loop on the first half of the clasp.
Repeat Step 4.
Repeat Step 3 to attach the strand to the second jumpring attached to the second loop on the second half of the clasp.
Cut one 12-inch length of Accu-Flex® beading wire. Repeat Step 3 to attach the wire to the first jumpring on the third loop on the first half of the clasp.
String onto the beading wire 3-1/2 inches of components.
Repeat Step 3 to attach the strand to the first hole on a 29x13mm flat back divine rock. Trim the excess wire from the end.
Repeat Step 3 to attach the excess wire to the opposite hole on the 29x13mm flat back divine rock.
String onto the beading wire enough components to equal the remaining length of the bracelet.
Repeat Step 3 to attach the strand to the first jumpring attached to the third loop on the second half of the clasp.
Cut one 12-inch length of Accu-Flex® beading wire. Repeat Step 3 to attach the wire to the second jumpring on the third loop on the first half of the clasp.
Repeat Step 4.
Repeat Step 3 to attach the strand to the second jumpring attached to the third loop on the second half of the clasp.
Have a question regarding this design idea? Email Customer Service.
The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.
All works of authorship (articles, videos, tutorials and other creative works) are from the Fire Mountain Gems and Beads® Collection, and permission to copy is granted for non-commercial educational purposes only. All other reproduction requires written permission. For more information, please email copyrightpermission@firemtn.com.