Triple-Strand Necklace and Earring Set with Crystal Passions® Beads and Embellishments and Almost Instant Jewelry®
Hover over to zoom.
Design Idea L324
Something Blue and New
-- Designer --
Jude, Jewelry Artist, Exclusively for Fire Mountain Gems and Beads®
To learn more about Jude Wroblewski, read her jewelry artist success story here.
: : : Materials : : :
Click here to view a full list of materials used in this design.
Please take the creative opportunity to select the products of your choice for this design, offered here at Fire Mountain Gems and Beads. Some materials may not be available or listed.
- Embellishment, Crystal Passions® rhinestone, crystal blue shade, foil back, 10mm faceted cushion fancy stone (4470)
- Ear wire, silver-plated brass, 16mm textured fishhook with open loop, 20 gauge
- Bead, Crystal Passions®, crystal light chrome, 3mm bicone (5328)
- Bead, Crystal Passions®, crystal light chrome, 3mm bicone (5328)
- Bead, cubic zirconia and silver-finished brass, clear, 9.5mm textured round
- Bead, Crystal Passions® and silver-plated pewter (tin-based alloy), Crystal Passions®, crystal blue shade, 3.8-4mm rose montées (53102), SS16
- Embellishment, Crystal Passions® rhinestone, crystal blue shade, foil back, 12mm faceted cushion fancy stone (4470)
- Crimp, sterling silver, 2mm cut tube with heavy wall, 1.2mm inside diameter
- Bead, Crystal Passions®, crystal blue shade, 6mm bicone (5328)
- Bead, Crystal Passions®, crystal blue shade, 6mm faceted round (5000)
- Bead, Crystal Passions®, crystal blue shade, 4mm faceted round (5000)
- Bead, Crystal Passions®, crystal blue shade, 4mm faceted round (5000)
- Seed bead, Dyna-Mites™, glass, silver-lined translucent pale blue, #11 round with square hole
- Clasp, toggle, silver-plated brass, 10mm round with woven texture and loops
- Drop, Almost Instant Jewelry®, silver-finished "pewter" (zinc-based alloy), 14mm square with 12mm cushion setting
- Drop, Almost Instant Jewelry®, silver-finished "pewter" (zinc-based alloy), 12mm square with 10mm cushion setting
- Crimp cover, silver-plated brass, 4mm round
- French wire, sterling silver, 1.2mm tube
- Eye pin, silver-plated brass, 2 inches, 21 gauge
- Beading wire, Accu-Flex®, nylon and stainless steel, clear, 49 strand, 0.019-inch diameter
- Jump ring, silver-plated brass, 4mm round, 2.4mm inside diameter, 20 gauge
Instructions
Necklace Instructions
Step 1
Cut the following:
- Three 16-inch lengths of Accu-Flex® professional-quality beading wire
- One 13-inch length of beading wire
- Five 1/2 inch lengths of French wire
Step 2
Mix Devcon® 5-Minute® Epoxy according to the adhesive instructions.
Apply a small amount of adhesive to a cushion setting then press in a 12mm cushion fancy stone. Repeat to set two more stones then set aside to cure.
Step 3
String a crimp and a length of French wire onto the 13-inch length of beading wire. Pass the beading wire back through the crimp. Pull the beading wire so the crimp rests snug against the French wire leaving approximately 1/4 inch of beading wire on the end. Crimp, trim the excess from the short end of the beading wire and add a crimp cover.
Step 4
String 21 sets of the following onto the beading wire:
- One blue shade 4mm round
- One pale blue #11 seed bead
- One light chrome 3mm bicone
- One seed bead
String the following:
- One blue shade montée
- One seed bead
- One 3mm bicone
- One seed bead
- One 4mm round
- One seed bead
- One 3mm bicone
- One seed bead
- One montée
- One seed bead
- One 3mm bicone
- One seed bead
- One 4mm round
Step 5
Repeat Step 3 to secure the strand. Add a 4mm jump ring to the French wire loop.
Step 6
Using the three 16-inch lengths of beading wire as one, string a crimp and a length of French wire. Pass the beading wires back through the crimp. Pull the beading wire so the crimp rests snug against the French wire leaving approximately 1/4 inch of beading wire on the end. Crimp, trim the excess from the short end of the beading wire and add a crimp cover.
Step 7
Continue to treat the three strands as one and string the following:
- Nine 6mm blue shade rounds
- Three sets of one 9.5mm cubic zirconia and silver-plated round and one 6mm blue shade bicone
- One 9.5mm cubic zirconia and silver-plated round
Step 8
Separate the three strands of beading wire.
On Strand 1, string one 3mm bicone then 11 sets of the following:
- One 4mm round
- One seed bead
- One 3mm bicone
- One seed bead
String crosswise through the first montée on the single beaded strand then three sets of the following:
- One seed bead
- One 3mm bicone
- One seed bead
- One 4mm round
Step 9
Repeat Step 3 to secure the strand.
Step 10
On Strand 2, string the following:
- One seed bead
- One 3mm bicone
- One seed bead
- One 3mm bicone
String 11 sets of the following:
- One 4mm round
- One seed bead
- One 3mm bicone
- One seed bead
String crosswise through the second montée on the single strand then four sets of the following:
- One seed bead
- One 3mm bicone
- One seed bead
- One 4mm round
Step 11
Repeat Step 3 to secure the strand.
Step 12
On Strand 3, string the following:
- One 3mm bicone
- One 4mm round
String 12 sets of the following:
- One seed bead
- One 3mm bicone
- One seed bead
- One 4mm round
String the following:
- One seed bead
- The jump ring on the end of the single strand
- One 3mm bicone
- One seed bead
- One 4mm round
String four sets of the following:
- One seed bead
- One 3mm bicone
- One seed bead
- One 4mm round
Step 13
Repeat Step 6 to secure the strand.
Step 14
Use 4mm jump rings to attach a fancy stone drop to each of the short ends of the three strands.
Step 15
Use 4mm jump rings to attach half of a toggle clasp to each end of the necklace.
Earring Instructions
Step 1
Mix Devcon 5-Minute Epoxy according to the adhesive instructions.
Apply a small amount of adhesive to a cushion setting then press in a 12mm cushion fancy stone. Repeat to set one more stone then set aside to cure.
Step 2
String three sets of the following onto an eye pin:
- One 3mm bicone
- One seed bead
- One 4mm round
- One seed bead
String one 3mm bicone then create a simple loop.
Repeat to create a second link.
Step 3
Use a 4mm jump ring to attach one link to an ear wire. Use a jump ring to attach a fancy stone drop to the opposite end of the link.
Repeat to complete a second earring.
Have a question regarding this project? Email Customer Service.
Copyright Permissions
The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.
All works of authorship (articles, videos, tutorials and other creative works) are from the Fire Mountain Gems and Beads® Collection, and permission to copy is granted for non-commercial educational purposes only. All other reproduction requires written permission. For more information, please email copyrightpermission@firemtn.com.