Single-Strand Necklace and Earring Set with Swarovski Crystal, Silver-Plated Brass Beads and Glass Bead

Necklace

STEP 1
Using flush-cutters, cut two 16-inch lengths of Accu-Flex® professional-quality beading wire.
STEP 2
String onto one 16-inch length of beading wire one silver-plated 2mm crimp bead. Pass the wire through the loop on one side of one silver-plated 14x7mm filigree oval clasp and back through the crimp bead. Place a small amount of gel adhesive inside the crimp (optional). Using the crimping pliers, crimp the crimp tube and trim excess wire. Place a 4mm silver-plated crimp cover over the crimp tube then gently close it.

Repeat Step 2 to attach the second length of beading wire to the opposite side of the clasp.
STEP 3
String the following components onto each of the two lengths of beading wire:
  • 4-1/2 inches of black hex 2-cut seed beads
  • Four silver-plated 6mm heishi beads
  • One silver-plated 6-pointed star 7mm bead cap
  • One black onyx 8mm round bead
  • One silver-plated 7mm 6-pointed star bead cap
  • Four silver-plated 6mm heishi beads
  • One silver-plated 7mm 6-pointed star bead cap
  • One black onyx 8mm round bead
  • One Swarovski crystal clear and silver-plated 8mm rondelle bead
  • One Swarovski crystal white 12mm crystal pearl
  • One Swarovski crystal clear and silver-plated 8mm rondelle bead
  • One black onyx 8mm round bead
  • One silver-plated 7mm 6-pointed star bead cap
  • Four silver-plated 6mm heishi beads
  • One silver-plated 7mm 6-pointed star bead cap
  • One black onyx 8mm round bead
  • One silver-plated 7mm 6-pointed star bead cap
  • Four silver-plated 6mm heishi beads
  • 1-inch of black hex 2-cut seed beads
STEP 4
Pass both strands of wire through the following components:
  • One black onyx 8mm round bead
  • One Swarovski crystal clear and silver-plate 8mm rondelle bead
  • One glass zebra pattern 26x6mm flat round bead
  • One silver-plated 7mm 6-pointed star bead cap
  • One silver-plated 6mm heishi bead
STEP 5
String the following components onto each of the two lengths of beading wire:
  • Five black hex 2-cut seed beads
  • Five silver-plated 6mm heishi beads
  • One silver-plated 7mm 6-pointed star bead cap
  • One black onyx 8mm round bead
  • One silver-plated 7mm 6-pointed star bead cap
  • Five silver-plated 6mm heishi beads
  • One silver-plated 7mm 6-pointed star bead cap
  • One black onyx 8mm round bead
  • One silver-plated 7mm 6-pointed star bead cap
  • Five silver-plated 6mm heishi beads
  • One silver-plated 7mm 6-pointed star bead cap
  • One black onyx 8mm round bead
  • One silver-plated 7mm 6-pointed star bead cap
  • Five silver-plated 6mm heishi beads
  • One silver-plated 2mm crimp bead
  • Six black hex 2-cut seed beads
  • One Swarovski jet 18x7.5mm wing bead
  • Six black hex 2-cut seed beads
STEP 6
Pass the straight end of the wire back through the crimp bead and pull crimp snug against the hex 2-cut seed beads. Place a small amount of gel adhesive inside the crimp (optional). Using the crimping pliers, crimp the crimp tube and trim excess from the short end of the wire. Place a 4mm silver-plated stardust crimp cover over the crimp tube then gently close it.

Repeat Step 6 to terminate the second strand.

Earrings

STEP 1
Using flush-cutters, cut two 2-inch lengths of beading wire.
STEP 2
String onto one length of beading wire one silver-plated 2mm crimp bead and the loop on one silver-plated kidney earwire. Pass the wire back through the crimp bead and pull snug against the earwire loop leaving a little slack for movement. Place a small amount of gel adhesive inside the crimp (optional). Using the crimping pliers, crimp the crimp tube and trim excess from the short end of the wire. Place a 4mm silver-plated stardust crimp cover over the crimp tube then gently close it.
STEP 3
String the following components onto the straight end of the wire:
  • One black onyx 8mm round bead
  • One silver-plated 7mm 6-pointed star bead cap
  • Five silver-plated 6mm heishi beads
  • One silver-plated 2mm crimp bead
  • Six black hex 2-cut seed beads
  • One Swarovski jet 18x7.5mm wing bead
  • Six black hex 2-cut seed beads
STEP 4
Pass the straight end of the wire back through the crimp bead and pull crimp snug against the hex 2-cut seed beads. Place a small amount of gel adhesive inside the crimp (optional). Using the crimping pliers, crimp the crimp tube and trim excess from the short end of the wire. Place a 4mm silver-plated stardust crimp cover over the crimp tube then gently close it.

Repeat Steps 2 - 4 to create a second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You