Two-Piece Necklace and Earring Set with Carnelian Gemstone Beads, Malaysia ''Jade'' Gemstone Beads and Swarovski Crystal

First Necklace

STEP 1
Cut one 14-inch length of Accu-Flex® professional-quality beading wire and two 5-inch lengths of 4mm rolo chain.
STEP 2
String onto the beading wire one 2x2mm crimp bead and one Accu-Guard™ wire protector. Pass the beading wire back through the crimp bead. Pull the beading wire so the crimp rests snug against the Accu-Guard leaving approximately 1/4 inch of beading wire on the end.

Crimp the crimp bead then trim the excess from the short end of the beading wire. Finish with a 4mm crimp cover.
STEP 3
String the following onto the beading wire, stringing one 4mm jumpring between each:
  • Two carnelian 8mm faceted rounds
  • One Malaysia ''jade'' fuchsia 4mm round
  • One carnelian 14x12mm flat oval
STEP 4
Continue to string the following:
  • One 4mm jumpring
  • One Malaysia ''jade'' fuchsia 6mm round
  • One 4mm jumpring
  • Three carnelian teardrops
  • One 4mm jumpring
  • One Malaysia ''jade'' fuchsia 4mm round
  • One 4mm jumpring
  • One Swarovski fuchsia 8mm round
  • One 4mm jumpring
  • One carnelian 3mm round
  • One 4mm jumpring
  • One Swarovski fuchsia 8mm round
STEP 5
Continue to string:
  • One 4mm jumpring
  • One Malaysia ''jade'' fuchsia 4mm round
  • One 4mm jumpring
  • One carnelian faceted rectangle
Repeat this sequence to string a total of seven sets.
STEP 6
Repeat the stringing sequence in Step 4 then Step 3 in the opposite direction to string the second half of the necklace. Repeat Step 2 to secure the strand.
STEP 7
Using one 4mm jumpring connect the first link on one length of rolo chain to the Accu-Guard on one end of the strand. Repeat to connect the second length of chain to the opposite end of the strand.

Using one 6mm jumpring connect one lobster claw clasp to the last link on the opposite end of one length of chain.

Using one 6mm jumpring connect a second 6mm jumpring to the second length of chain.

Second Necklace

STEP 1
String the following onto one 2-inch headpin:
  • One Malaysia ''jade'' fuchsia 4mm round
  • One 4mm jumpring
  • One carnelian faceted rectangle
  • One 4mm jumpring
  • One Malaysia ''jade'' fuchsia 4mm round
Form a simple loop on the straight end of the wire.
STEP 2
String one 5x5mm double cone onto one 2-inch headpin then form a simple loop. Repeat to create a second double cone drop.
STEP 3
String onto one 2-inch headpin one carnelian 3mm round, one 4mm jumpring and one Malaysia ''jade'' fuchsia 4mm round then form a simple loop. Repeat to create a second carnelian and jade drop.
STEP 4
String the hole in one 23.5mm hammered open round drop onto one 2-inch headpin then form a simple loop. Attach one 6mm jumpring to the loop.
STEP 5
Using 6mm jumprings attach the drops from Steps 1 - 3 to the ring drop in the following order:
  • One double cone drop
  • Two 6mm jumprings
  • One carnelian and jade drop
  • Two 6mm jumprings
  • The carnelian rectangle drop
  • Two 6mm jumprings
  • One carnelian and jade drop
  • Two 6mm jumprings
  • One double cone drop
STEP 6
Cut one 17-inch length of 3x2.5mm cable chain.
STEP 7
Using one 4mm jumpring connect one lobster claw clasp to the first link on the length of chain.

String the ring drop onto the chain then attach one 6mm jumpring to the last link.

Earrings

STEP 1
String onto one 2-inch headpin one carnelian 3mm round, one 4mm jumpring and one Malaysia ''jade'' fuchsia 4mm round then form a simple loop. Repeat to create a total of fourteen carnelian and jade drops.
STEP 2
Using a 4mm jumpring attach one carnelian and jade drop to each loop on one 23mm hoop earring. Repeat to create a second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You