Single-Strand Necklace and Earring Set with Silver-Finished "Pewter" and Enamel Charms, Silver-Finished Brass Charms and Celestial Crystal® Beads

Necklace

STEP 1
Cut two 6-inch lengths of long and short oval chain, one 4-inch length of cable chain and one 20-inch length of Accu-Flex® professional-quality beading wire.
STEP 2
Pass one 1-1/2 inch headpin through one blue 3mm bicone then form a simple loop to create one blue bicone drop. Repeat to create a total of 6 blue bicone drops.

Repeat, using one clear 4mm bicone in place of the blue 3mm bicone, to create one clear bicone drop. Repeat to create a total of three clear bicone drops.
STEP 3
Pass the 4-inch length of cable chain through one 15x5mm curved tube bead so 1-1/2 inches of the chain hangs from the left side of the tube and 2-1/2 inches hang from the right.

Pass one 4mm jump ring through one link of the cable chain just inside the right portion of the curved tube and the loop of one clear bicone drop then close. Repeat to secure one clear bicone drop to the first link of cable chain inside the left side of the curved tube to secure the chain in place.
STEP 4
Use one 4mm jump ring to connect one 22mm snowflake charm to the short end of the cable chain. Use one 4mm jump ring to connect one 13mm snowflake charm to the long end of the cable chain.

Continue to use 4mm jump rings to connect four more 13mm snowflake charms, one more 22mm snowflake charm and the remaining bicone drops to the cable chain as you see fit to complete the necklace component.
STEP 5
String onto the 21-inch length of beading wire: one crimp and one Accu-Guard™ wire protector. Pass the beading wire back through the crimp. Pull the beading wire so the crimp rests snug against the Accu-Guard leaving approximately 1/4 inch of beading wire on the end. Crimp, then trim the excess from the short end of the beading wire.
STEP 6
String the following on the beading wire:
  • Two sets of:
    • One 7x5mm bead cap
    • One blue 6mm bicone
  • Two sets of:
    • One blue 6mm bicone
    • One 7x5mm bead cap
  • One clear 6mm bicone
  • One blue 3mm bicone
  • One clear 6mm bicone
  • Two sets of:
    • One blue 6mm bicone
    • One 7x5mm bead cap
  • One 7x5mm bead cap
  • One blue 6mm bicone
  • One 7x5mm bead cap
  • Two sets of:
    • One 7x5mm bead cap
    • One blue 6mm bicone
  • One clear 6mm bicone
  • One blue 3mm bicone
  • One clear 6mm bicone
  • Two sets of:
    • One blue 6mm bicone
    • One 7x5mm bead cap
  • One 7x5mm bead cap
  • One blue 6mm bicone
  • Two sets of:
    • One blue 6mm bicone
    • One 7x5mm bead cap
  • One clear 6mm bicone
  • Two sets of:
    • One 7x5mm bead cap
    • One blue 6mm bicone
  • Two sets of:
    • One blue 6mm bicone
    • One 7x5mm bead cap
STEP 7
Continue to string the necklace component onto the beading wire then repeat Step 6 in the opposite direction.

Repeat Step 5 to secure the strand.
STEP 8
Use one 4mm jump ring to connect one Accu-Guard on the strand to the end of one 6-inch length of oval chain. Repeat to connect the remaining Accu-Guard to the end of the second 6-inch length of oval chain.

Use one 4mm jump ring to connect the remaining end of the first length of oval chain to the loop on one half of one toggle clasp. Repeat to connect the end of the second length of oval chain to the loop on the second half of the toggle clasp.

Earrings

STEP 1
Cut two 1-inch lengths of cable chain.
STEP 2
Pass one 1-1/2 inch head pin through one blue 3mm bicone then form a simple loop to create one blue bicone drop. Repeat to create a total of six blue bicone drops.

Repeat, using one clear 4mm bicone in place of the blue 3mm bicone, to create one clear bicone drop. Repeat to create a total of three clear bicone drops.
STEP 3
Use one 4mm jump ring to connect one 22mm snowflake charm to the end of one length of cable chain.

Repeat using the second length of cable chain.
STEP 4
Use one 4mm jump ring to connect one 13mm snowflake charm approximately halfway up one length of cable chain. Continue to use 4mm jump rings to connect three blue bicone drops and one clear bicone drop above the 13mm snowflake charm.

Repeat, using the second length of cable chain and the remaining bicone drops.
STEP 5
Use one 4mm jump ring to connect the remaining end of one length of cable chain to the loop of one ear wire.

Repeat using the second 1-inch length of cable chain to create a second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.