Fire Mountain Gems and Beads

Bracelet and Earring Set with Miyuki Beads, Seed Beads and TierraCast Links

MD32

Tiled Paths


: : : Materials : : :

  • Bead, Miyuki, half TILA, glass, opaque matte satin brown, 5x2.3mm rectangle (102 beads)
  • Bead, Miyuki, half TILA, glass, opaque matte satin dark orange, 5x2.3mm rectangle (82 beads)
  • Bead, Miyuki, half TILA, glass, opaque matte metallic patina iris, 5x2.3mm rectangle (79 beads)
  • Seed bead, Delica, glass, opaque matte metallic rainbow dark green, #11 round
  • Seed bead, Miyuki, glass, opaque metallic rainbow green, #15 rocaille
  • Link, TierraCast, antique brass-plated pewter (tin-based alloy), 11.5x7mm double-sided oasis with 2 loops (4 links)
  • Jump ring, antique gold-plated brass, 8x6mm oval, 16 gauge (4 jump rings)
  • Clasp, 2-strand slide lock, antique gold-plated brass, 16x6mm tube (1 clasp)
  • Ear wire, antique brass-plated steel, 19mm fishhook with 3mm ball and 2mm coil with open loop, 22 gauge (2 ear wires)
  • Pliers, bent-nose
  • Pliers, chain-nose
  • Pliers, flush-cutter
  • Thread, Berkley FireLine, gel-spun polyethylene, smoke, 0.10mm diameter, 3-pound test

  • Optional

  • Thread

-- Designer --

LauraLynn, Jewelry Designer, Exclusively for Fire Mountain Gems and Beads®

To learn more about LauraLynn, read her jewelry artist success story here

Bracelet

STEP 1
Cut a 6-foot length of thread.

Thread a needle onto one end, almost doubling the thread but leaving a tail so you are only working with one thread.

Note: It may be necessary to cut additional lengths of thread. If you are nearing the end of your thread, weave the needle through 5-6 adjacent beads to secure the thread then trim excess thread. Thread the needle onto a new length of thread then pass the needle through 5-6 beads, exiting the bead where you left off then continue beading.

Starting the End

STEP 2
Pass the beading needle through one hole on the 2-hole side of an oasis link. Pick up two metallic rainbow green #15 rounds, one dark orange 5x2.3mm half Tila® and two metallic rainbow green #11 rounds then pass the needle through the second hole of the link.

Pass the beading needle through one hole on the 2-hole side of an oasis link. Pick up two metallic rainbow green #15 rounds, one brown 5x2.3mm half Tila and two metallic rainbow green #11 rounds then pass the needle through the second hole of the link.

First Row

STEP 3
Pick up:
  • One matte metallic rainbow dark green #11 round
  • One brown half Tila
  • The second hole of the brown half Tila from Step 2
  • One brown half Tila
  • One matte metallic rainbow dark green #11 round
  • One matte metallic patina iris half Tila
  • One matte metallic rainbow dark green #11 round
  • One dark orange half Tila
  • The second hole of the dark orange half Tila from Step 2
  • One dark orange half Tila
  • One matte metallic rainbow dark green #11 round

Second Row

STEP 4
Pick up one matte metallic patina iris half Tila then pass the needle back through the second hole of the last dark orange half Tila from Step 3. Pick one dark orange half Tila then pass the needle through the second hole of the other dark orange half Tila from Step 3.

Pick up one matte metallic rainbow dark green #11 round then pass the needle through the second hole of the matte metallic patina iris half Tila from Step 3.

Continue working this pattern with the brown half Tila beads for the second half of the row, ending with a matte metallic patina iris half Tila.

Continue the Pattern

STEP 5
Pass the beading needle back through the top hole of the matte metallic patina iris half Tila then continue adding rows following the pattern in Steps 3 and 4 until the desired length of bracelet is completed.

Repeat Step 2 to secure the opposite end using oasis links.

Trim excess thread.

Adding the Fringe

STEP 6
Thread the beading needle onto a new length of thread. Pass the needle through 5-6 beads, exiting the matte metallic patina iris half Tila on one end of the bracelet (through the hole closest to end).

Pick up three metallic rainbow green #15 rounds then pass the needle back through the second hole of the half Tila. Pass the needle through the first hole of the next matte metallic patina iris half Tila along the same edge then pick up three more metallic rainbow green #15 rounds.

Repeat this pattern to add fringe along the edge.
STEP 7
After adding the last fringe to the first edge, pass the needle through the row to the opposite side, exiting the hole of the half Tila closest to the links.

Repeat Step 6 to add fringe to the second edge. Pass the needle through a few adjacent beads to secure then trim excess thread.

Adding the Clasp

STEP 8
Pass one jump ring through one loop of half of the slide lock clasp and one oasis link then close. Repeat to attach the second loop of the clasp to the second oasis link on one end.

Repeat to attach the second half of the clasp to the opposite end to finish the bracelet.

Earrings

STEP 1
Cut a 3-foot length of thread.

Thread a beading needle, almost doubling the length but leaving a tail so you are only working with one thread.
STEP 2
Pick up ten sets of:
  • One matte metallic dark green #11 round
  • One brown half Tila

Pass the needle through the first set of #11 round and half Tila then pull tight, forming a circle.
STEP 3
Pass the needle back through the top hole of the current half Tila in the opposite direction then pick up two matte metallic dark green #11 rounds.

Pass the needle through the top hole of the next brown half Tila then pick up two more #11 rounds.

Continue this pattern to form the outer circle using the half Tila beads. Pass the beading needle through 5-6 adjacent beads to secure then trim excess thread.
STEP 4
Add an ear wire to the outer circle between two of the #11 rounds.
STEP 5
Repeat Steps 1 - 4 to create a second earring.

: : : Additional Resources : : :

  • ''Using Accu-Guard™ Wire Protectors'' how-to video and illustrated instructions
  • ''How to Create the Fringe Stitch'' how-to video and illustrated instructions
  • ''Thread a Needle with Ease, How-To'' illustrated instructions

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.


  • Email:info@firemtn.com
  • Customer Service: (800) 423-2319
  • Order by Phone: (800) 355-2137
  • Order by Fax: (800) 292-3473

Fire Mountain Gems and Beads - One Fire Mountain Way, Grants Pass, OR 97526-2373
Copyright 2023 All rights reserved.