Multi-Strand Necklace and Earring Set with Gunmetal-Plated Steel Focal, Black Onyx Gemstone Cabochon and Glass Rhinestone and Gunmetal-Finished Brass Cupchain

Necklace

STEP 1
Using flush-cutters cut the following:
  • Two 3-1/2 inch lengths, two 4-3/4 inch lengths, two 5-1/5 inch lengths and two 5-3/4 inch lengths of gunmetal-plated 6mm filigree round chain
  • Two 4-1/2 inch lengths, two 5-1/2 inch lengths, and one 7-inch length of 4mm light red cupchain
  • Two 3-1/2 inch lengths and two 6-inch length of 4mm black cupchain
  • Two 2-1/2 inch lengths and one 7-inch length of 2mm clear cupchain
  • Two 3-3/4 inch lengths of 2mm light red rhinestone cupchain
STEP 2
String one Swarovski light Siam 6mm bicone onto an eyepin. Using a pair of chain-nose pliers, round-nose pliers and flush-cutters, form a simple loop on the straight end of the eyepin. Repeat to create a total of two Swarovski light Siam 6mm bicone beading links.
STEP 3
Place a thin layer of Loctite® gel adhesive in the center of the gunmetal-plated 46mm wavy flower focal and on the back of the 12mm round black onyx cabochon. Press the cabochon onto the center of the wavy flower focal. Let the adhesive set. Make sure to use proper ventilation when using this product.
STEP 4
Using a pair of chain-nose pliers and flat-nose pliers, open a 4.5mm jumpring. Pass it through the loop on the lobster claw clasp and the loop on a Swarovski light Siam 6mm bicone beading link. Close the jumpring.

Open a 4.5mm jumpring. Pass it through the opposite loop on the Swarovski light Siam 6mm bicone beading link and the top hole on a gunmetal-plated 4-loop end bar. Close the jumpring.

Repeat to attach a Swarovski light Siam 6mm bicone beading link to a 6mm jumpring and a second gunmetal-plated 4-loop end bar.
STEP 5
Place a small dab of Loctite gel into the bottom of a gunmetal-plated 2.5x2.5mm cupchain connector. Insert the first cupchain link on a 3-3/4 inch length of 2mm light red cupchain. Using flat-nose pliers, gently bend the cupchain connector prongs over the cupchain link. Repeat to attach a cupchain connector to the opposite link on the 3-3/4 inch length of 2mm light red cupchain.

Repeat to attach a cupchain connector to:
  • The first and last links on two 3-3/4 inch length of 2mm light red cupchain
  • The first and last links on two 4-1/2 inch lengths of 4mm light red cupchain
  • The first and last links on two 3-1/2 inch lengths of 4mm black cupchain
  • The first and last links on two 2-1/2 inch lengths of 2mm clear cupchain
  • The first link on two 5-1/2 inch lengths and one 7-inch length of 4mm light red cupchain
  • The first link on two 6-inch lengths of 4mm black cupchain
  • The first link on one 7-inch length of 2mm clear cupchain
STEP 6
Open a 4.5mm jumpring. Pass it through first loop on the first gunmetal-plated 4-loop end bar and the first link on a 5-1/5 inch length of gunmetal-plated 6mm filigree round chain. Close the jumpring. Repeat to attach a 4.5mm jumpring to the last link of the 5-1/5 inch length of gunmetal-plated 6mm filigree round chain and the cupchain connector attached to the first link on a 3-3/4 inch length of 2mm light red cupchain.

Orient the gunmetal-plated 46mm wavy flower focal like a clock with 12 o'clock at the top. Open a 6mm jumpring. Pass it through the cupchain connector attached to the last link on a 3-3/4 inch length of 2mm light red cupchain and through the filigree on the wavy flower focal between the petals at 9 and 10 o'clock .

Repeat to attach a 4-3/4 inch length of gunmetal-plated 6mm filigree round chain and a 3-1/2 inch length of 4mm black cupchain to the second loop on the first gunmetal-plated 4-loop end bar and the wavy flower focal between the petals at 9 and 10 o'clock .

Repeat to attach a 3-1/2 inch length of gunmetal-plated 6mm filigree round chain and a 4-1/2 inch length of 4mm light red cupchain to the third loop on the first gunmetal-plated 4-loop end bar and the wavy flower focal on the petal at 10 o'clock .

Repeat to attach a 5-3/4 inch length of gunmetal-plated 6mm filigree round chain and a 2-1/2 inch length of 2mm clear cupchain to the fourth loop on the first gunmetal-plated 4-loop end bar and the wavy flower focal between the petals at 10 and 11 o'clock .
STEP 7
Repeat Step 6 backwards to create a mirror image of the first part of the necklace.
STEP 8
Open a 6mm jumpring. Pass it through the cupchain connector attached to the first link on a 7-inch length of 4mm light red cupchain and through the wavy flower focal on the petal at 6 O’clock.

Repeat to attach a 5-1/2 inch length of 4mm light red cupchain and through the flower focal on the petal at 7 o'clock and between the petals at 4 and 5 o'clock .

Repeat to attach a 6-inch length of 4mm black cupchain and through the wavy flower focal between the petals at 6 and 7 o'clock and on the petal at 5 o'clock .

Repeat to attach a 7-inch length of 2mm clear cupchain and through the wavy flower focal between the petals at 5 and 6 o'clock .

Earrings

STEP 1
Using flush-cutters cut the following:
  • Two 2-1/2 inch lengths of 4mm light red cupchain
  • Two 2-1/2 inch lengths of 4mm black cupchain
  • Two 2-1/2 inch lengths of 4mm clear cupchain
  • Two 2-1/2 inch lengths of 2mm clear cupchain
  • Two 2-1/2 inch lengths of 2mm light red cupchain
STEP 2
String one Swarovski light Siam 6mm bicone onto an eyepin. Using a pair of chain-nose pliers, round-nose pliers and flush-cutters, form a simple loop on the straight end of the eyepin. Repeat to create a total of two Swarovski light Siam 6mm bicone beading links.
STEP 3
Place a small dab of Loctite gel into the bottom of a gunmetal-plated 2.5x2.5mm cupchain connector. Insert the first cupchain link on a 2-1/2 inch length of 2mm light red cupchain. Using flat-nose pliers, gently bend the cupchain connector prongs over the cupchain link. Make sure to use proper ventilation when using this product.

Repeat to attach a cupchain connector to:
  • The first link on two 2-1/2 inch lengths of 2mm light red cupchain
  • The first link on two 2-1/2 inch lengths of 2mm clear cupchain
  • The first link on two 2-1/2 inch lengths of 4mm light red cupchain
  • The first link on two 2-1/2 inch lengths of 4mm clear cupchain
  • The first link on two 2-1/2 inch lengths of 4mm black cupchain
STEP 4
Using a pair of chain-nose pliers and flat-nose pliers, open the loop on a Swarovski light Siam 6mm bicone beading link. Pass it through the loop on a leverback earwire. Close the loop.

Open the opposite loop on the Swarovski light Siam 6mm bicone beading link. Pass it through the top hole on a gunmetal-plated 4-loop end bar. Close the loop.
STEP 5
Open a 4.5mm jumpring. Pass it through the loop on a 2-1/2 inch length of 4mm light red cupchain and the first loop on the gunmetal-plated 4-loop end bar.

Repeat to attach the following to the gunmetal-plated 4-loop end bar:
  • One 2-1/2 inch length of 4mm clear cupchain to the second loop
  • One 2-1/2 inch length of 2mm light red cupchain
  • One 2-1/2 inch length of 2mm clear cupchain to the third loop
  • One 2-1/2 inch length of 4mm black cupchain to the fourth link
STEP 6
Repeat Steps 4 and 5 to create the second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You