Multi-Strand Necklace, Bracelet and Earring Set with Swarovski Crystal and Dione® Large-Hole Beads

Necklace

STEP 1
Mix Devcon® 5 Minute® Epoxy according to manufacturer’s instructions. Place a thin layer of adhesive on the inside rim of the antiqued gold-plated 34mm round setting and on the back of the Swarovski crystal glacier blue 30mm flat back. Press the flat back into the setting. Let the adhesive set for 5 minutes. Make sure to use proper ventilation when using this product.
STEP 2
Using a pair of chain-nose pliers and bent-nose pliers, open one 5mm jumpring. Pass it through the 4mm jumpring attached to the lobster claw clasp. Close the jumpring.

Repeat to attach one 5mm jumpring to the opposite 4mm jumpring.

Repeat to attach one 15mm twisted jumpring to the loop on the top of the crystal glacier blue mounted focal.
STEP 3
Using flush-cutters, cut one 21-inch and four 15-inch lengths of Accu-Flex® professional-quality beading wire. String onto the wire: one crimp tube, one gold-plated Accu-Guard™ wire protector and the 5mm jumpring attached to the lobster claw clasp. Pass the wire back through the crimp tube, leaving one end of the wire approximately 1-inch long. Pull the crimp tight against the Accu-Guard. Place a small amount of adhesive (Loctite®) inside the crimp (optional).

Using the crimping pliers, crimp the crimp tube. Using flush-cutters, trim the excess wire from the short end.

Place a stardust crimp cover over the crimp tube then gently close it.
STEP 4
String onto the 21-inch length of beading wire after the crimp beads the following:
  • One Swarovski cream 8mm round pearl
  • One gold-plated 3mm crimp cover
  • Five Swarovski cream 8mm round pearls
  • One Swarovski cream 10mm round pearl
STEP 5
String onto the beading wire one crimp bead. Pass the end of the four 15-inch beading wires through the crimp bead on the first strand. Make sure there is no slack along the length of the first strand. Place a small amount of gel adhesive inside the crimp (optional). Using the crimping pliers, crimp the crimp tube. Using flush-cutters, trim excess wire from the short end of the 15-inch beading wires.
STEP 6
String onto all five lengths of beading wire after the crimp bead the following:
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead (positioned over the crimp)
  • One Dione® gold-plated and crystal clear 14mm pavé bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
Separate the beading wires and string twelve Swarovski cream 3mm round pearls onto each of the five lengths of wire.

Group the strands together again and string onto all five lengths of beading wire the following:
  • One gold-plated and Swarovski crystal clear 10x3.5mm crystal rondelle bead
  • One Swarovski white 14mm Becharmed pearl bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm crystal rondelle bead
Separate the beading wires and string twelve Swarovski cream 3mm round pearls onto each of the five lengths of wire.

Group the strands together again and string onto all five lengths of beading wire the following:
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • One Dione gold-plated and crystal clear 12mm bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
Separate the beading wires and string twenty-four Swarovski cream 3mm round beads onto each of the five lengths of wire.

String onto all five lengths of beading wire after the crimp bead the following:
  • The 15mm jumpring attached to the crystal glacier blue mounted focal (positioned over the center of the five strands of cream 3mm round pearls)
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • One Dione gold-plated and crystal clear 12mm bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
Separate the beading wires and string twelve Swarovski cream 3mm round pearls onto each of the five lengths of wire.

Group the strands together again and string onto all five lengths of beading wire the following:
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • One Swarovski white 14mm Becharmed pearl bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
Separate the beading wires and string twelve Swarovski cream 3mm round pearls onto each of the five lengths of wire.
STEP 7
Bring the strands of wire together and string one crimp bead onto all five wires. Make sure there is no slack along the length of the strands. Place a small amount of gel adhesive inside the crimp (optional).Using the crimping pliers, crimp the crimp tube. Using flush-cutters, trim excess wire from the short end of the 15-inch beading wire. Place a crimp cover over the crimp tube then gently close it.
STEP 8
Continue to string onto the 20-inch length beading wire:
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead (positioned over the crimp)
  • One Dione gold-plated and crystal clear 12mm bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • One Swarovski cream 10mm round pearl
  • Five Swarovski cream 8mm round pearls
  • One gold-plated 3mm crimp cover
  • One Swarovski cream 8mm round pearl
STEP 9
String onto the beading wire: one crimp bead, one gold-plated Accu-Guard and the 5mm jumpring attached to the opposite 4mm jumpring on the lobster claw clasp. Pass the wire back through the crimp bead, pulling the wire tight against the last bead. Make sure there is no slack along the length of the necklace. Place a small amount of gel adhesive inside the crimp (optional).

Using the crimping pliers, crimp the crimp bead. Using flush-cutters, trim excess wire from the end. Place a stardust crimp cover over the crimp bead and gently close it using chain-nose pliers.

Bracelet

STEP 1
Using a pair of chain-nose pliers and bent-nose pliers, open one 5mm jumpring. Pass it through the 4mm jumpring attached to the lobster claw clasp. Close the jumpring. Repeat to attach a second 5mm jumpring next to the first.

Repeat to create a chain of three sets of one 5mm jumpring and one 8mm jumpring.
STEP 2
Using flush-cutters cut one 12-inch length of Accu-Flex beading wire. String onto the wire: one crimp tube, one gold-plated Accu-Guard and the 5mm jumpring attached to lobster claw clasp. Pass the wire back through the crimp tube, leaving one end of the wire approximately 1-inch long. Pull the crimp tight against the Accu-Guard. Place a small amount of adhesive (Loctite) inside the crimp (optional).

Using the crimping pliers, crimp the crimp tube. Using flush-cutters, trim the excess wire from the short end.

Place a crimp cover over the crimp tube then gently close it.
STEP 3
String onto the beading wire the following:
  • Three sets of one Swarovski cream 12mm round pearl and one gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • One Dione gold-plated and crystal clear 14mm bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • Three sets of one Swarovski cream 12mm round pearl and one gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • One Dione gold-plated and crystal clear 14mm bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • Two sets of one Swarovski cream 12mm round pearl and one gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • One Dione gold-plated and crystal clear 14mm bead
  • One gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • Two sets of one Swarovski cream 12mm round pearl and one gold-plated and Swarovski crystal clear 10x3.5mm rondelle bead
  • One Swarovski cream 12mm round pearl
STEP 4
String onto the beading wire: one crimp bead, one gold-plated Accu-Guard and the last 5mm jumpring attached jumpring chain made in Step 1. Pass the wire back through the crimp bead, pulling the wire tight against the last bead. Make sure there is no slack along the length of the bracelet. Place a small amount of gel adhesive inside the crimp (optional).

Using the crimping pliers, crimp the crimp bead. Using flush-cutters, trim excess wire from the end. Place a crimp cover over the crimp bead and gently close it using chain-nose pliers.

Earrings

STEP 1
String one Swarovski cream 8mm round pearl onto an eyepin. Using a pair of chain-nose pliers, round-nose pliers and flush-cutters, form a simple loop on the straight end of the wire. Repeat to create two Swarovski cream 8mm round pearl links.

Repeat to create two 10mm pearl drops using one Swarovski cream 10mm round pearl, one gold-plated Swarovski crystal clear 10x3.5mm rondelle bead, one Swarovski cream 10mm round pearl and one headpin.
STEP 2
Using a pair of chain-nose pliers and bent-nose pliers, open the loop on the top of the Swarovski cream 8mm round pearl link. Pass it through the loop on the earwire. Close the loop. Open the opposite loop on the Swarovski cream 8mm round pearl link. Pass it through the loop on one cream 10mm pearl drop.
STEP 3
Repeat Step 2 to create the second earring.

: : : Additional Resources : : :

The pieces featured in the Gallery of Designs are copyrighted designs and are provided for inspiration only. We encourage you to substitute different colors, products and techniques to make the design your own.

Have a question regarding this design idea? Email Customer Service.

Recommended Just for You