Q: Does crimping or gluing work best to hold beads on a stick pin?

Q: While creating a wire wrap for a very large faceted lemon quartz briolette, I inadvertently caused chipping on each side of the top-drilled hole. I've decided not to use the stone as a briolette since the drill hole is no longer useful. Can I repair the damage and what then can I do with the stone?

Q: If gluing seed beads to a flat surface, is there a spray or glue to put on top to make sure they stay smooth and secure to the object?

Q: If the half-drilled pendant findings or screw eyes are too large, what is a good substitute?

Q: I'm interested in doing silver clay jewelry. What's the best way to get started? I love marcasite. Can I put them in the silver clay and then heat or is it best to glue them in later. Would I use jewelry glue or slip?

Q: How do I attach a clasp to ball chain? What type of clasp do I use?

Q: What kind of knot do you tie when using elastic cord for a bracelet so it is secure when you're done beading?

Q: I want to make a necklace out of small tiles, but I can't put a hole in them. I need a type of ring to glue on the top to put the beads through. What is it called, and how do I find them?

Q: How do I use ribbon ends on my loomworked bracelets? Every time I attach one I crush some of the beads because the clamp doesn't seem large enough to cover the beads. I've seen other examples of loom and off-loom bracelets with these ends attached, but I don't know how to properly attach them. Do you have any bar clasps that are made specifically for stitched bracelets and necklaces or some kind of instructional resource on how to use the ribbon clasp on beadwork?

Q: What are your items that will hold Faceted Gems and Cabochons? Is it best to use glue? If so, what kind?

Q: I have discovered the joys (and tribulations) of working with jumprings in making chainmaille jewelry. Besides soldering the rings closed, is there a special glue that can be used? I love working with jumprings of all sizes and would like to know that the jewelry I make will stay together. Thank you!!

Q: What type of earring settings can I use for an undrilled pearl? I have a pair of perfectly matched pearls and I hate the setting they are in. I just want to reset them so I can wear them. They are approximately 4mm.

Q: I've been watching your videos on peyote stitch and you don't show how to attach a clasp at the end. I like wide bracelets and can't figure out how to finish the piece. Thank you.

Q: I bought some metal beads that go onto the ends of memory wire. The hole doesn't go all the way through. How do I keep that end bead on the memory wire?

Q: I have a pretty rose cabochon with petals that can't be set in a bezel. Should I wire wrap it—if so, how do I do this? Thank you.

Q: How do you use liquid solder? Do you have to use a torch? I am an amateur but need to know how to close silver jump rings.

Q: I make beaded barrettes. I have tried to use glue to hold down the beadwork but eventually the glue doesn't hold. I sew beadwork onto leather/suede, should I sew through the leather/suede and the bottom part of the barrette? What is better to use, Nymo® thread or wire?

Q: I have two questions: 1) How do you glue a cabochon into a setting that doesn't have a back? If I glue around the edge, I still have problems with it being too easy for the cabochon to come off. 2) Besides the metal settings that are sold, are there other ways to create a setting that would allow a cabochon to become a pendant without drilling a hole in the cabochon? Thanks.

Q: I purchased Accu-Flex® beading wire and crimp ends to make bracelets. The crimp ends just fit on the end of the cord; will this be secure enough if I crimp with a crimper, or is there more to be done, maybe a drop of glue?

Q: I am winding paper that is sparkly on one side and smooth on the other and when I go to glue it I can't get it to adhere and the bead becomes unwound. Help!

Q: I have dried glue on some of my tools. I'd like to know what to use to safely remove it. I'm also ordering your 'stuff' for dipping the tips for wireworking. When I have the tips coated, is that going to interfere with using them for future projects? If so, should I purchase a separate set?

Q: I made a couple of gemstone chip bracelets on Power cord, but I don't like the way they turned out. The knot area, with a small dab of glue on it, is stiff and brittle. The cord seems to have "warped" and appears to be stretched out of shape. The chips slid on the cord easily so that would not seem to be the reason for this distortion of the cord. Help!

Q: I use Devcon's two part epoxy 30-min. for my metal jewelry projects. I have had a few customers contact me because their jewelry came apart--esp. during the winter. Does it become brittle? How do I fix this problem?

Q: I want to "trim" the edge of a seashell with silver. I definitely do not want to just glue metal on. Is there some way to attach metal to a shell? Could I perhaps even use metal clay?